Earthquaker Devices - Crimson Drive  [traced]

General documentation, gut shot, schematic links, ongoing circuit tracing, deep thoughts ... all about boutique stompboxes.
User avatar
Hides-His-Eyes
Tube Twister
Information
Posts: 1940
Joined: 02 Feb 2010, 12:34
Has thanked: 50 times
Been thanked: 51 times

Post by Hides-His-Eyes »

culturejam wrote:That would certainly put an end to my blind, fumbling suppositions. :lol:
aww, I was having fun.
Testing, testing, won too fwee

User avatar
Dirk_Hendrik
Old Solderhand
Information
Posts: 4193
Joined: 03 Jul 2007, 08:44
Location: Old Amsterdam
Has thanked: 232 times
Been thanked: 887 times
Contact:

Post by Dirk_Hendrik »

drawn. Some stuff to check though. At least 2 suspicions of design errors and one major piece of wondering (elctrolit with normal cap in series).

FET input buffer, Ge gain stage, asymm. clipping.
Sorry. Plain out of planes.

http://www.dirk-hendrik.com

User avatar
justaddsomeecho
Information
Posts: 10
Joined: 19 Nov 2010, 19:43
Has thanked: 1 time
Been thanked: 4 times

Post by justaddsomeecho »

oh, thank you :D

User avatar
Chugs
Resistor Ronker
Information
Posts: 277
Joined: 16 May 2009, 09:47
Has thanked: 63 times
Been thanked: 47 times

Post by Chugs »

I would have put the gain control after the buffer. Between the 1uf and 0.1uf.

Maybe they originally had the gain control between the 1uf and 0.1uf but decided they liked it better on the input and then never bother changing the 1uf/o1uf in series because they liked how it sounded. :scratch:

User avatar
Dirk_Hendrik
Old Solderhand
Information
Posts: 4193
Joined: 03 Jul 2007, 08:44
Location: Old Amsterdam
Has thanked: 232 times
Been thanked: 887 times
Contact:

Post by Dirk_Hendrik »

whups!
Minor errors corrected:
EartQuaker_Devices_Crimson_Drive.pdf
(9.16 KiB) Downloaded 1585 times
Sorry. Plain out of planes.

http://www.dirk-hendrik.com

User avatar
Dirk_Hendrik
Old Solderhand
Information
Posts: 4193
Joined: 03 Jul 2007, 08:44
Location: Old Amsterdam
Has thanked: 232 times
Been thanked: 887 times
Contact:

Post by Dirk_Hendrik »

Some comment on those big ass electrolits.

The Ge stage has gain. Shiteloads of gain. This means that any power supply, including my lab-supply introduces hum over the voltage supply lines which is automatically amplified in the Ge Stage. (It's fine with a battery). Considering the supply filtering I suspect that the builder of this thing ran into the same issue and added extra supply filtering.
Sorry. Plain out of planes.

http://www.dirk-hendrik.com

User avatar
Ice-9
Degoop Doctor
Information
Posts: 1094
Joined: 31 Mar 2009, 15:29
my favorite amplifier: Marshall
Completed builds: Far to many to afford the enclosures for them all. :)
Has thanked: 134 times
Been thanked: 359 times
Contact:

Post by Ice-9 »

I suspect that C4 and C5 in series could probabaly be left over from the original design this circuit was made from that didn't incorperate true bypass. Marshall use a similar config to power the led when using a dpdt instead of a 3pdt, usually there would be a 10k ish resistor between the two caps.

Just speculating a reason for these caps, I could be way off and he might of just stuck C5 in there to change the sound a bit. :)
It's fairly straight forward, if you want to start it , press start. You can work out the rest of the controls for yourself !

No silicon heaven ? preposterous ! Where would all the calculators go ?

User avatar
culturejam
Old Solderhand
Information
Posts: 4062
Joined: 24 Feb 2008, 05:59
Has thanked: 433 times
Been thanked: 563 times
Contact:

Post by culturejam »

Couple electronics-noobish questions...

I've never seen anyone use a power supply filter cap like how C7 is used. At least I assume that's the point of it (to reduce noise)?

Q1 is used as a buffer, right? So Q2 is doing all the "work" in terms of amplifying the signal?

R5 and R8 are there for stabilizing the bias of Q2, doing away with the need for a bias trimmer?

User avatar
Hides-His-Eyes
Tube Twister
Information
Posts: 1940
Joined: 02 Feb 2010, 12:34
Has thanked: 50 times
Been thanked: 51 times

Post by Hides-His-Eyes »

D1 and D4... Surely you would want those the other way round? Give it 9V the wrong way and the signal diode would short out before you could say "oh bollocks" wouldn't it?
Testing, testing, won too fwee

User avatar
Hides-His-Eyes
Tube Twister
Information
Posts: 1940
Joined: 02 Feb 2010, 12:34
Has thanked: 50 times
Been thanked: 51 times

Post by Hides-His-Eyes »

Also does the current setup not lead to Z_in of only 100k?
Testing, testing, won too fwee

User avatar
Dirk_Hendrik
Old Solderhand
Information
Posts: 4193
Joined: 03 Jul 2007, 08:44
Location: Old Amsterdam
Has thanked: 232 times
Been thanked: 887 times
Contact:

Post by Dirk_Hendrik »

Better learn to say bollocks fast then. What you ask is what i didn't expect either (and therefore doublechecked).

And... yes. So what? 100k is a perfectly round and easy to remember number. That's simple so it must be tone heaven. :mrgreen:
Sorry. Plain out of planes.

http://www.dirk-hendrik.com

User avatar
Dirk_Hendrik
Old Solderhand
Information
Posts: 4193
Joined: 03 Jul 2007, 08:44
Location: Old Amsterdam
Has thanked: 232 times
Been thanked: 887 times
Contact:

Post by Dirk_Hendrik »

culturejam wrote:Couple electronics-noobish questions...

I've never seen anyone use a power supply filter cap like how C7 is used. At least I assume that's the point of it (to reduce noise)?
The use of AC decoupling on emitters in amplifier stages is a fairly common thing . C7 does not function as a PS filter cap here.

culturejam wrote: Q1 is used as a buffer, right? So Q2 is doing all the "work" in terms of amplifying the signal?

R5 and R8 are there for stabilizing the bias of Q2, doing away with the need for a bias trimmer?
yes, Yes, No (setting the bias, not stabilizing) ,Yes but be careful. With the wide variation between Ge Trannies a fixed setup will not always give optimal performance.
Sorry. Plain out of planes.

http://www.dirk-hendrik.com

User avatar
mictester
Old Solderhand
Information
Posts: 2923
Joined: 11 Sep 2008, 20:29
my favorite amplifier: Mesa Boogie, Roost Sessionmaster, AC30
Completed builds: Hundreds! Mostly originals, a few clones and lots of modifications.
Location: Somewhat closer to Amsterdam than before!
Has thanked: 32 times
Been thanked: 844 times
Contact:

Post by mictester »

Dirk_Hendrik wrote:drawn. Some stuff to check though. At least 2 suspicions of design errors and one major piece of wondering (elctrolit with normal cap in series).

FET input buffer, Ge gain stage, asymm. clipping.
The electrolytic was probably an output for buffered bypass, with the 100n as the input to the gain stage.
"Why is it humming?" "Because it doesn't know the words!"

User avatar
culturejam
Old Solderhand
Information
Posts: 4062
Joined: 24 Feb 2008, 05:59
Has thanked: 433 times
Been thanked: 563 times
Contact:

Post by culturejam »

Dirk_Hendrik wrote:The use of AC decoupling on emitters in amplifier stages is a fairly common thing . C7 does not function as a PS filter cap here.
Ah yes, how silly of me.

Dirk_Hendrik wrote:With the wide variation between Ge Trannies a fixed setup will not always give optimal performance.
That's what I was thinking, which is why I questioned the lack of trimmer.

Thanks, Dirk!

User avatar
Dirk_Hendrik
Old Solderhand
Information
Posts: 4193
Joined: 03 Jul 2007, 08:44
Location: Old Amsterdam
Has thanked: 232 times
Been thanked: 887 times
Contact:

Post by Dirk_Hendrik »

mictester wrote:
Dirk_Hendrik wrote:drawn. Some stuff to check though. At least 2 suspicions of design errors and one major piece of wondering (elctrolit with normal cap in series).

FET input buffer, Ge gain stage, asymm. clipping.
The electrolytic was probably an output for buffered bypass, with the 100n as the input to the gain stage.
Yeps. With a possible bypass mute in between as suggested above. Would make sense with the electrolit orientation like this.
Sorry. Plain out of planes.

http://www.dirk-hendrik.com

User avatar
azrael
Cap Cooler
Information
Posts: 564
Joined: 02 Jun 2009, 14:07
Has thanked: 35 times
Been thanked: 88 times

Post by azrael »

So what exactly does C7 do?

User avatar
WhiteKeyHole
Cap Cooler
Information
Posts: 546
Joined: 05 Apr 2008, 04:38
Has thanked: 24 times
Been thanked: 220 times

Post by WhiteKeyHole »

As Dirk said, it's an AC bypass capacitor. Remember, Q2 is PNP.

User avatar
azrael
Cap Cooler
Information
Posts: 564
Joined: 02 Jun 2009, 14:07
Has thanked: 35 times
Been thanked: 88 times

Post by azrael »

Oh crap, you're right. Totally overlooked that. :slap:

User avatar
RnFR
Old Solderhand
Information
Posts: 4879
Joined: 09 Jan 2008, 06:02
my favorite amplifier: Traynor YBA-III, Fender Super Six
Completed builds: custom fuzz.
Location: Inner Earth
Has thanked: 139 times
Been thanked: 133 times
Contact:

Post by RnFR »

kind of like a buffered Ge electra. as simple as this circuit is, at least it's somewhat "original".
isn't that anti-pop 2M2 a bit redundant with the gain control on the input? or would the coupling cap negate that feature?
when using a PNP in an NPN circuit like this, it can help to separate the supplies for each with their own current limiting resistors and decoupling caps. this can help with the "motorboating" oscillation you might get.
my guess on those series caps is the gain control move- i seriously doubt a pedal co like this would have buffered bypass in any of their pedals. either that, or it's just there to fuck us up! :wink:
i'd like to see what's happening inside their Mantra box. i kind of like the dark snarly tone that thing has.
"You've converted me to Cubic thinking. Where do I sign up for the newsletter? I need to learn more about how I can break free from ONEism Death Math." - Soulsonic

Blog-APOCALYPSE AUDIO

User avatar
culturejam
Old Solderhand
Information
Posts: 4062
Joined: 24 Feb 2008, 05:59
Has thanked: 433 times
Been thanked: 563 times
Contact:

Post by culturejam »

RnFR wrote:kind of like a buffered Ge electra. as simple as this circuit is, at least it's somewhat "original".
Yeah, my first thought was a buffered Beavis Trotsky (germanium Electra).

Post Reply