Skreddy Lunar Module [traced]
Very much like the screwdriver except for 3 high gain BC109C's.
http://i42.tinypic.com/1r9maf.jpg
http://i40.tinypic.com/oabw94.jpg
http://i42.tinypic.com/1r9maf.jpg
http://i40.tinypic.com/oabw94.jpg
- Skreddy
- Resistor Ronker
Information
The very first Screw Driver prototype used all BC109C's as I recall. This was before I decided to do away with having each section of the circuit individually switched.
At one point I began using Mena Suvari inside, but that quickly became too expensive.
At one point I began using Mena Suvari inside, but that quickly became too expensive.
- RnFR
- Old Solderhand
Information
that is awesome.
"You've converted me to Cubic thinking. Where do I sign up for the newsletter? I need to learn more about how I can break free from ONEism Death Math." - Soulsonic
Blog-APOCALYPSE AUDIO
Blog-APOCALYPSE AUDIO
- culturejam
- Old Solderhand
Information
schematic up for grabs and free for all. Enjoy.
Partslist
Part Value Device Package Library Sheet
BODY A100K POT POT custom-pots 1
BRITE B100k POT POT custom-pots 1
C1 10µF 0501 050_020_1 custom-caps-electro-pol 1
C2 100pF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C3 100µF 0501 050_020_1 custom-caps-electro-pol 1
C4 5.6nF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C5 4.7nF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C6 220nF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C7 470pF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C8 220pF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C9 220pF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C10 100µF 0501 050_020_1 custom-caps-electro-pol 1
C11 15nF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C12 3.3nF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C13 2nF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
D1 green LED5MM LED5MM custom-diodes 1
D2 BAT48 1N4148-2 DO35-2 custom-diodes 1
FUZZ A1k POT POT custom-pots 1
PREGAIN B2k POT POT custom-pots 1
Q1 BC109C 2N2369 TO18 custom-trans 1
Q2 BC109C 2N2369 TO18 custom-trans 1
Q3 BC109C 2N2369 TO18 custom-trans 1
R1 56k 6MM.3 R0207/3 custom-resistors 1
R2 470k 6MM.3 R0207/3 custom-resistors 1
R3 18k 6MM.3 R0207/3 custom-resistors 1
R4 100 6MM.3 R0207/3 custom-resistors 1
R5 10k 6MM.3 R0207/3 custom-resistors 1
R6 100k 6MM.3 R0207/3 custom-resistors 1
R7 100 6MM.3 R0207/3 custom-resistors 1
R8 820 6MM.3 R0207/3 custom-resistors 1
R9 100 6MM.3 R0207/3 custom-resistors 1
R10 100k 6MM.3 R0207/3 custom-resistors 1
R11 56k 6MM.3 R0207/3 custom-resistors 1
R12 56k 6MM.3 R0207/3 custom-resistors 1
R13 10k 6MM.3 R0207/3 custom-resistors 1
R14 2.7k 6MM.3 R0207/3 custom-resistors 1
VOLUME A100K POT POT custom-pots 1
Partslist
Part Value Device Package Library Sheet
BODY A100K POT POT custom-pots 1
BRITE B100k POT POT custom-pots 1
C1 10µF 0501 050_020_1 custom-caps-electro-pol 1
C2 100pF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C3 100µF 0501 050_020_1 custom-caps-electro-pol 1
C4 5.6nF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C5 4.7nF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C6 220nF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C7 470pF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C8 220pF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C9 220pF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C10 100µF 0501 050_020_1 custom-caps-electro-pol 1
C11 15nF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C12 3.3nF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
C13 2nF 050X030_0252 050X030_025_2 custom-caps-ceramic 1
D1 green LED5MM LED5MM custom-diodes 1
D2 BAT48 1N4148-2 DO35-2 custom-diodes 1
FUZZ A1k POT POT custom-pots 1
PREGAIN B2k POT POT custom-pots 1
Q1 BC109C 2N2369 TO18 custom-trans 1
Q2 BC109C 2N2369 TO18 custom-trans 1
Q3 BC109C 2N2369 TO18 custom-trans 1
R1 56k 6MM.3 R0207/3 custom-resistors 1
R2 470k 6MM.3 R0207/3 custom-resistors 1
R3 18k 6MM.3 R0207/3 custom-resistors 1
R4 100 6MM.3 R0207/3 custom-resistors 1
R5 10k 6MM.3 R0207/3 custom-resistors 1
R6 100k 6MM.3 R0207/3 custom-resistors 1
R7 100 6MM.3 R0207/3 custom-resistors 1
R8 820 6MM.3 R0207/3 custom-resistors 1
R9 100 6MM.3 R0207/3 custom-resistors 1
R10 100k 6MM.3 R0207/3 custom-resistors 1
R11 56k 6MM.3 R0207/3 custom-resistors 1
R12 56k 6MM.3 R0207/3 custom-resistors 1
R13 10k 6MM.3 R0207/3 custom-resistors 1
R14 2.7k 6MM.3 R0207/3 custom-resistors 1
VOLUME A100K POT POT custom-pots 1
- Skreddy
- Resistor Ronker
Information
FYI: The above schematic is completely wrong in a number of places. Remember: this is exactly the same topology as the Screw Driver but with different parts.
If you are referring to the missing 100uF on the supply and the reverse orientations of some of the pots, that will be fixed later after i have had a chance to put it on my protoboard and test it out. Some of your labeling doesn't correlate with actual components used and the lug numbering on the pots doesn't match with what is there either. Just plain wrong. My reversal is only as good at best as the "wrongness" of the board.
- Skreddy
- Resistor Ronker
Information
You traced it completely wrong. Sorry if that sounds like an insult or something. Not my fault you didn't trace it right.Damon Jonesta wrote:If you are referring to the missing 100uF on the supply and the reverse orientations of some of the pots, that will be fixed later after i have had a chance to put it on my protoboard and test it out. Some of your labeling doesn't correlate with actual components used and the lug numbering on the pots doesn't match with what is there either. Just plain wrong. My reversal is only as good at best as the "wrongness" of the board.
Not insulted at all. I've re-traced it 3 times and basically got the same thing except for the 100uF at the supply and some orientation issues. Maybe it is wrong... We'll just have to see if it's completely wrong like you said, in which case it will sound like a POS, or if it works. If it's wrong then it's the trace, but you can't denied the lug labels on your PCB is in error. Just saying.
- culturejam
- Old Solderhand
Information
If Mr. Skreddy says there are major errors, then it is so. I'm not taking sides here, but history has shown him to be an honest, forthcoming guy. Your effort is still appreciated, however.Damon Jonesta wrote:Not insulted at all. I've re-traced it 3 times and basically got the same thing except for the 100uF at the supply and some orientation issues. Maybe it is wrong... We'll just have to see if it's completely wrong like you said, in which case it will sound like a POS, or if it works. If it's wrong then it's the trace, but you can't denied the lug labels on your PCB is in error. Just saying.
And I don't think he said "completely wrong", for the record.
- Skreddy
- Resistor Ronker
Information
Damon Jonesta wrote:Not insulted at all. I've re-traced it 3 times and basically got the same thing except for the 100uF at the supply and some orientation issues. Maybe it is wrong... We'll just have to see if it's completely wrong like you said, in which case it will sound like a POS, or if it works. If it's wrong then it's the trace, but you can't denied the lug labels on your PCB is in error. Just saying.
Sorry; my bad. A couple of drinks and I lose all sensibility. It's just drawn differently, but your schemo looks like everything connects to everything else in the right way.
- RnFR
- Old Solderhand
Information
that was good for a larf!! thanks for the schemo! both of you!
"You've converted me to Cubic thinking. Where do I sign up for the newsletter? I need to learn more about how I can break free from ONEism Death Math." - Soulsonic
Blog-APOCALYPSE AUDIO
Blog-APOCALYPSE AUDIO
are you serious? Did you get your beard all messy.Skreddy wrote:Damon Jonesta wrote:Not insulted at all. I've re-traced it 3 times and basically got the same thing except for the 100uF at the supply and some orientation issues. Maybe it is wrong... We'll just have to see if it's completely wrong like you said, in which case it will sound like a POS, or if it works. If it's wrong then it's the trace, but you can't denied the lug labels on your PCB is in error. Just saying.
Sorry; my bad. A couple of drinks and I lose all sensibility. It's just drawn differently, but your schemo looks like everything connects to everything else in the right way.
Any way, C15 is missing from your PCB.
And so is C16... not on the board at all... Did ebay sell me a defective copy?
I only saw 2-3 differences. Not exactly "completely".
seriously check your lug numbering. It's all backwards.
Thanks for the schemo. You are an example for us all
NVM about the c15, c16. Jut saw your post.
You should use my schemo. It looks better
You should use my schemo. It looks better
Drinkin' on a Wednesday... I knew there was a reason beyond pedals I love this guy! Thanks for the schemo too. So what are ya drinkin'? I've cut back lately and I've really been craving Guiness and other fine stouts. Wolavers Cream Stout... yuuummmmSkreddy wrote:Yeah, I'm a dork when I'm drunk.RnFR wrote: that was good for a larf!! thanks for the schemo! both of you!
- Whoismarykelly
- Resistor Ronker
Have you met yourself? Seriously the guy gives you his official schematic after saying you have errors on your tracing attempt and you still talk shit.Damon Jonesta wrote:NVM about the c15, c16. Jut saw your post.
You should use my schemo. It looks better