This looks great, and if I can see ahead to any time to build one I may order a PCB from you on eBay (assuming you have any left by then!).

To revive discussion of the 'typist' erasers mentioned above - they are still available: I found some on http://www.erasersticks.com/block-erasers.html and one at https://www.aroundtheoffice.com/Richard-Best-Pencil-Style-Typist-Eraser-4421-Typewriter-Erasers-Eraser-Sticks/productinfo/ER-4421-BN I ha...

I would certainly also be interested in the schematic if it can be reposted!

P90s have a lot of wire in them, so they need as large a cancelling coil as any single-coil you are likely to encounter. The fact that it is only one pickup doesn't make much difference to what you need either - pickups are usually selected in parallel, which gives (pretty much) the average of the s...

..Except that it encourages a race to the bottom in price: as no device can then be guaranteed to be of its 'rated' value, all devices must then be treated as suspect and the price (and margins) fall. This is very bad for the bottom line in the longer term, so the question is really whether the manu...

I don't know how much a cheap wah pedal would cost you locally (I'm in Australia) but in case it is competitive with your market, Small Bear Electronics (http://smallbear-electronics.mybigcommerce.com/) sell a wah shell with rack for US$47.00 plus postage. I have myself picked up electronically dead...

For various reasons, it is not possible to edit a post except in the few minutes after it is posted.

Ice-9 is suggesting that you solder a piece of component lead from the (most appropriate) existing solder point to the spot where you need to solder in a replacement component. IE: replace the damaged track with a piece of wire. Sorry if that doesn't make it any clearer. I have done the same when re...

Your enclosures look brilliant, and you have obviously put a lot of thought into the design! Like most posters so far, I am not sure I can justify spending so much for an enclosure and switch when I would normally get both for $10 - $15, but the cost does seem justified for such a complex item in lo...

Regarding voltage - the maximum 'acceptable' voltage depends on what the voltage source is pushing it into and what sound you want. What will be clipped in the following circuit (and whether that sounds good) is largely up to the next thing in line. There are plenty of pedals that use an 18V supply ...

When you say "old fashioned UK aerial socket", I don't know if that would be banana , BNC , a Belling-Lee connector (which I think is the one we still use in Australia) or even an F connector . If it is BNC, most modern oscilloscope probes use it - just get a modern set with sufficient ban...

I would be happy if most of those I got were 300 hfe or higher, personally.

I would like to register my interest in purchasing some of these - how many will likely be determined by the price...

I think I placed the order in December. If they are discontinued, that is a shame, as it seems to be really good for the price. If you want to build something equivalent and you are comfortable working with mains power, R.G. Keen has an article on building a multi-isolated-output power supply (which...

Well, I ended up getting the Fame DCT-200 from Musicstore.com myself. Apart from the fuss I ended up dealing with regarding international bank transfers (my bank here in Australia defaulted to a transaction type that, along with my unfamiliarity with international bank transfers, created unnecessary...

If you did the coats in fairly quick succession, you will find that the base coats will still be rubbery/soft after the top coats have dried. Thus any hard pressure/impact will cause the base coats to 'give' underneath the top coats. You may simply need to give it more time for the base coats to exp...

I have had a few more tries with this on powdercoated Pedal Parts Plus boxes. The results have been mixed - it always leaves the paint matt in places, but some finishes come up pretty well if a clear coat is added over the top. The worst problem is using press+peel blue leaves blue traces in the fin...

My 2c... You don't need to spend much at all if you look around - I scored a single-trace BWD 509B for AU$26.00 (plus a 50 minute round trip to collect) on Ebay recently. It is a locally made analog scope (they were widely used in Melbourne schools in the '80s), which I got without probes - I am cur...

That sounds like a guitar tone control circuit with treble bleed cap for the volume...

Dr Nomis, would you mind sharing the brand name of your spray clear? I have had bad experiences with clear coats so far - I have tried two, one crazes when it dries (which looks quite cool sometimes, but weakens the finish and leads to flaking) and the other tends to develop fisheye and other incons...