Wow, I have the same pedal that also has those wires in the back. The wires on mine are green though.......... my unit has a huge NOISE issue as you constantly hear the LFO going through the audio (even in unmodulatoed settings). Really annoying. I was really wondering if someone had just modded min...

Anyone got a schematic of this? I already mailed George Dennis but still no answer......

I got a unit that doenst work anymore. Only a very faint clean tone..... no true bypass

I've had some time and checked the schematic

Believe now it is fine!

Here's the LED switching part of the OCD V2.0

I don't know the value of D4 and C19

Greetings!!

These FS36999 transistors are really 2N5133; I just fixed a '73 Ramshead Big Muff that had a transistor that was partially printed as 2N5133 and partially FS36999

https://www.instagram.com/p/B6O7_ISnUuz ... hare_sheet

I got one in; here's the schematic!
Notice that the diodes are zener diodes

Hi! 1. All solder joints look identical. I do think there was someone who looked inside the unit, as it was missing two screws...... as yet, I find no real evidence of tampering 2. I thought this also, BUT the unit was made in Thailand. Most pedals from Boss at that timeframe came from Japan. As to ...

Hi all! As of lately, I havent been posting that much on here as my job as my two newborn sons really take a lot of time...... But lately, I've been digging into this 'mystery' and I hope you can help me! I've been looking into 'Chaser' pedals (or 'Chazer' as the fonts aren't that readable) I got th...

Bernardduur wrote:

pablomago wrote:What reverb tank did you put in your QSB II? I have a few small tanks around.

I'll check when I'm home!

It is a P-RMOD-8AB2A1B

pablomago wrote:What reverb tank did you put in your QSB II? I have a few small tanks around.

I'll check when I'm home!

Here is the schematic of my unit
Mods: Please change the name of the thread to Masotti - Black box

Hey all!

Anyone knows what kind of footswitch this is?
It is from a ISP decimator and it is broken.

My amp became a lot more quiet with new caps. I also added a zobel network

Would anyone know the value of Q2? (located underneath the mix knob??) I have one on the bench that had worked before but now the unit won't turn on. I tested the unit but the TL062 gets no power. I can trace the V+ up until Q2, then I lose it. Q2 looks really bad (like burned) so my best quess was ...

Here's the power supply!

I know that v3205 work with limited power supply like 7V. Try limiting V+2 at 7V if it start to work. Bye Thanks! I tried limiting it by adding back the 100R resistor on the ground of the adapter jack. I removed that one because it worked on a 'standard' battery for years and that battery gave me m...

On my way fixed the problem

R80 was shot because C13 short circuited. C13 is a bypass capacitor and is located near U2. When removed the problems were over (after replacing R80 with a 10R resistor)

According to this site R80 is 10R

I've tried replacing the resistor with another 10R with no succes. The voltages of the board are still below 2V

Busy with tracing this unit........ very slow more information is available.

Hi all! I have this old Pearl AD-08 that uses a MN3205 and a MN3102. It broke like a month ago without any real issues. Upon inspection all seemed to function except for my MN3205. I scope the signal up to the input of the BBD where it disappears. I tried it with a V3205 without succes. The BIAS set...

Maybe I overlooked a small trace between 4/13 and ground. I'll check it again!