Search found 89 matches
- 14 Feb 2017, 21:03
- Forum: Boutique Stompboxes dissected...
- Topic: Catalinbread - Dirty Little Secret [traced]
- Replies: 447
- Views: 242782
Re: Catalinbread - Dirty Little Secret [traced]
If you are referring to taper for the Presence pot....I used a linear or 'B', taper....works fine!
- 25 Jan 2017, 02:32
- Forum: Vintage Stompbox Corner ( ... - 1975)
- Topic: A/DA - Final Phase [schematic]
- Replies: 22
- Views: 21860
Re: A/DA - Final Phase [schematic]
I'm not sure which version you based your build off of....but this is the reissue frequency reading. I took frequency readings at the test point (pin 10) of the 4047. With all controls CCW and the Range control CW, I measured: min. 34kHz max. 537kHz The reissue CV is 15 volts. The original is 5 volt...
- 23 Aug 2016, 22:31
- Forum: Modern Stompbox Effects (1975 - ...)
- Topic: Musitronics - Mu-Tron - Flanger - C130 [schematic]
- Replies: 76
- Views: 42876
Re: Musitronics - Mu-Tron - Flanger - C130 [schematic]
Check your post on the other site.
- 18 Aug 2016, 21:42
- Forum: Modern Stompbox Effects (1975 - ...)
- Topic: Musitronics - Mu-Tron - Flanger - C130 [schematic]
- Replies: 76
- Views: 42876
Re: Musitronics - Mu-Tron - Flanger - C130 [schematic]
Will, The descriptions of your problem, "they do not seem to work", "I am not getting any response" are very vague.
If you could be so kind as to expand on the problem you are encountering...maybe someone here can offer some suggestions.
If you could be so kind as to expand on the problem you are encountering...maybe someone here can offer some suggestions.
- 25 May 2016, 15:47
- Forum: Vintage Stompbox Corner ( ... - 1975)
- Topic: Ibanez - FP-777 Flying Pan
- Replies: 55
- Views: 31830
Re: Ibanez - FP-777 Flying Pan
Thanks for that Bernardduur! I recently checked the factory schematic against available board shots. Are you sure that the (red-trace side) 470K between C27 & R21 goes to Vref2? I see the Vref2 trace running under the 470K, and the 470K connected to the ground side of uninstalled R20. Also…good ...
- 29 Mar 2016, 04:13
- Forum: Modern Stompbox Effects (1975 - ...)
- Topic: DOD - 585 A Analog Delay [schematic]
- Replies: 12
- Views: 8872
- 19 Aug 2015, 19:30
- Forum: Modern Stompbox Effects (1975 - ...)
- Topic: EHX - Octave Multiplexer [schematic]
- Replies: 70
- Views: 47860
Re: EHX - Octave Multiplexer [schematic]
I said I would post pictures of my Octave Multiplexer in another threat. I will do so naturally. But I feel a little stupid now that I googled it a bit. It's been traced already - and very well - factory schematic... http://topopiccione.atspace.com/PJ19EHOctaveMultiplexer.html Here are my pictures ...
- 06 Aug 2015, 06:41
- Forum: Modern Stompbox Effects (1975 - ...)
- Topic: Maxon - AD-900 MN3008 version [schematic]
- Replies: 10
- Views: 11144
Re: Maxon - AD-900 MN3008 version [schematic]
Just so I'm clear..the repeats are what sound "dark" to me with the AD-900 I actually did experiment with the filter values of the DM2. I built a daughter board for the AD-900 to switch different filter sections in.....it didn't work too well. For some reason that I don't understand...it c...
- 20 Jun 2015, 15:17
- Forum: Vintage Stompbox Corner ( ... - 1975)
- Topic: Colorsound - Flanger [schematic]
- Replies: 10
- Views: 8317
Re: Colorsound - Flanger [schematic]
Here is a preview of my progress with the board. Lacking trace side images, I used component side shots for reference for the component placement. There were two versions of the Colorsound Flanger. The schematics previously posted and this board layout reflect the second version which seems to have ...
- 19 Jun 2015, 04:48
- Forum: Modern Stompbox Effects (1975 - ...)
- Topic: Boss - CS-2 Compressor Sustainer [schematic]
- Replies: 49
- Views: 27150
Re: Boss - CS-2 Compressor Sustainer [schematic]
Google "BA662 vs BA6110 thread, again" this will show you how to replace the BA662 with a BA6110 and four transistors.
I have researched then implemented this retrofit in the Boss VB-2 circuit.
I have researched then implemented this retrofit in the Boss VB-2 circuit.
- 17 Jun 2015, 17:43
- Forum: Vintage Stompbox Corner ( ... - 1975)
- Topic: SolaSound - Tonebender 1971 [schematic]
- Replies: 30
- Views: 19177
Re: SolaSound TB late '60 [pics, schematic] [schematic]
Why couldn't you have received a Colorsound flanger for repair?
I'm working on the board routing and....I could use a few trace side shots!
I'm working on the board routing and....I could use a few trace side shots!
- 17 Jun 2015, 00:48
- Forum: Vintage Stompbox Corner ( ... - 1975)
- Topic: Elektronika - Synchro Wah [schematic]
- Replies: 6
- Views: 5928
Re: Elektronika - Synchro Wah [schematic]
I think it's a radio sending unit for KGB agents sent to infiltrate and spy on those dissident Rock and Roll musicians!
- 15 Jun 2015, 15:54
- Forum: Modern Stompbox Effects (1975 - ...)
- Topic: Maxon - AD900 Analog Delay [schematic]
- Replies: 57
- Views: 52021
Re: Maxon - AD900 Analog Delay [schematic]
So...that's what it sounds like after you messed with the trimmers?
You were warned!
You were warned!
- 15 Jun 2015, 14:35
- Forum: Vintage Stompbox Corner ( ... - 1975)
- Topic: Tycobrahe - Parapedal [schematic]
- Replies: 97
- Views: 70009
Re: Tycobrahe - Parapedal [schematic]
Was that really a necessary comment?kymar wrote:I think you turned this thread in Pedal Debugging & Troubleshooting Support.
Are you the forum police?
- 15 Jun 2015, 13:27
- Forum: Vintage Stompbox Corner ( ... - 1975)
- Topic: Colorsound - Flanger [schematic]
- Replies: 10
- Views: 8317
Re: Colorsound - Flanger [schematic]
After I posted the redrawn schematics, I started working on identifying components from original board images to make a layout. While focusing my attention around the rotary switch, I noticed that the original drawing depicts the switching sequence as: Manual, Auto, ADT. That is incorrect. The origi...
- 15 Jun 2015, 13:15
- Forum: Vintage Stompbox Corner ( ... - 1975)
- Topic: Tycobrahe - Parapedal [schematic]
- Replies: 97
- Views: 70009
Re: Tycobrahe - Parapedal [schematic]
At this point....I'm out of ideas. I would get rid of the sockets for the resistor and diode. Solder those components to the PCB directly. There seems to be intermittent bias voltage issues at pins 3 and 5 of the op amps. Some voltage readings are in the ballpark and then next readings the bias is o...
- 14 Jun 2015, 22:17
- Forum: Vintage Stompbox Corner ( ... - 1975)
- Topic: Colorsound - Flanger [schematic]
- Replies: 10
- Views: 8317
Re: Colorsound - Flanger [schematic]
Here are the redrawn schematics: https://dl.dropboxusercontent.com/u/53299166/DIYstompboxes/Colorsound%20Flanger%20pg.1.jpg https://dl.dropboxusercontent.com/u/53299166/DIYstompboxes/Colorsound%20Flanger%20pg.2.jpg I verified as many components as possible from images available on the net. If you we...
- 13 Jun 2015, 13:56
- Forum: Vintage Stompbox Corner ( ... - 1975)
- Topic: Tycobrahe - Parapedal [schematic]
- Replies: 97
- Views: 70009
Re: Tycobrahe - Parapedal [schematic]
Okay...
You still have something going on.
The voltages from your reply @ 17:15 had the reference voltage at 2.9V...now it's down to 1.3V.
Pull the op amps and take voltages again.
Take a close up picture of the whole component side of the board.
You still have something going on.
The voltages from your reply @ 17:15 had the reference voltage at 2.9V...now it's down to 1.3V.
Pull the op amps and take voltages again.
Take a close up picture of the whole component side of the board.
- 13 Jun 2015, 02:58
- Forum: Vintage Stompbox Corner ( ... - 1975)
- Topic: Tycobrahe - Parapedal [schematic]
- Replies: 97
- Views: 70009
Re: Tycobrahe - Parapedal [schematic]
Not Jim's post... Intripped's post.
- 13 Jun 2015, 02:56
- Forum: Vintage Stompbox Corner ( ... - 1975)
- Topic: Tycobrahe - Parapedal [schematic]
- Replies: 97
- Views: 70009
Re: Tycobrahe - Parapedal [schematic]
Did you read Jim's post? I never thought to check your resistor values because ...I thought you would have double checked that before ever asking for help. with R14 a 1K instead of a 1M pull down...you are pulling the signal down to ground! No wonder the signal disappears at the beginning of the cir...