I need help with were i put the in and out signal for this one tube reverb on a peavey windsor head. .

[attachment=0]class_a_subminiature_schematic_amp.gif[/attachment

I was wondering if I have the right order of number for my tube. V1a 1 2 4 etc. Thanks

How would I go about modifying the output section to make this work with with a single ended transformer? I only have a hammond 1750a.this is what I have built so far.I just wired 1 & 8 together on tube 6111 for now. I got sound but not loud.Thanks.

Is it possible to substitute the 5672 tube with a 6112? Thanks

I have no sound when I turn the effect on. I used sabrotone http://www.sabrotone.com/wp-content/uploads/2012/10/TripleWreck.gif I wired it like this http://www.sabrotone.com/?attachment_id=3472. My voltage are: IC1 1 4.70 2 4.70 3 3.20 4 0 5 3.19 6 4.71 7 4.71 8 9.42 IC2 1 4.66 2 4.69 3 4.67 4 0 5 4...

I just built this version Rah.gif . Can I just replace R12 with a 2.2 resistor to get more gain and keep my 500k gain pot to control how much gain I want. 2.2K? Increasing R12 will decrease the amount of treble boost in that stage, making it a little darker with less overall gain. So do you or anyb...

I posted this above, but does anyone know what to change to get more volume out of the pedal when the gain is below 12 o'clock? Reduce R14, 15? In addition, do other people find the bass control has an overly exaggerated bass sweep, from telephone like to way too much oomph? I can only find one swe...

I just built this version Rah.gif . Can I just replace R12 with a 2.2 resistor to get more gain and keep my 500k gain pot to control how much gain I want. 2.2K? Increasing R12 will decrease the amount of treble boost in that stage, making it a little darker with less overall gain. So do you or anyb...

I've been messing about with this on the breadboard a bit today ahead of building one, and I ended up changing the gain control. I liked it best with the gain almost maxed, so I got rid of the existing gain pot, the 47p treble bleed and 47n coupling cap, and just wired the 100n (C7 on the schem) di...

Just built this pedal it sounds pretty good. One problem I have is after I play my guitar for a little while then stop the pedal will make some weird crackle sound like when you remove your guitar cord before shutting down your amp. All my cords are new. I re-soldered everything and I re-checked all...

2013-12-13 20.01.39.jpg I got it to work but it has low volume everything is maxed out.I had my amp up to 6 on clean channel just had to remember to turn my guitar before I turned the pedal off. Got vr1 to 4.5 volts and higher it just got farty. I turned vr2 up to the max to get it to be a little l...

No I did not I have to get some. Now I have no sound. It pops when I try to turn up vr2. So I got no clue anymore. I tripled checked everything. Is there some way to test the board to see where the problem is like with a multimeter. I copied ever thing from the verifed mkiii to the tee.

Is this how you connect the trimpots ? Once again I am new to this and thanks for the help.

my volts is 9.5 I cannot get it to go down any more. it just shut off and I only turn it a 1/16 of a turn and it is full blast. the diagram you post is version 5 just making sure cause you wrote 6. Ok thanks

ok I got everything corrected now when I try to turn up vr1 it just crackly. I got everything on the pedal half way.

pinkjimiphoton wrote:i'll be kinda chillin' around the homestead today, so if i can help hit me up.

Ok I will. Thanks for helping

the higher the collector voltages, the louder it should get. try 6-7 volts on q1 would you happen to have the schematic for the toneblaster mkiii . I believe my problem is that I am using the toneblaster mk 2.5 design by you drawn by kodiakkluub ver 4. my tr1 is in the wrong spot. I don't have vero...

This is the one I built the toneblaster mkiii at the bottom of the first page The only problem that I have is it is not loud for some reason I have the pedal and guitar cranked to 10. Is there something I can do thanks

ThanksGonna try this one is it possible to use 30k for r7 and vr2 instead of 22k? I have only 1 100k trimpot which I plan to use on Q1. Is it possible to use a 50k trimpot for vr2?

I got the right parts. When I turn the tone knob down is it normal to lose so much volume? I am gonna have a look at the toneblaster. Is there gonna be much of a different between this one and the toneblaster? thanks