Hi all,

So I'm done with the pedal and it works fine now. As I haven't found anybody else posting a build report I thought I may just write my own.

I'm a fan of the small Solid Metal (AION makes one, too, they call it the Ember Distortion). So I really wanted the Pro version as well.

1. The Pro version gives you way more control.
2. The Pro version has lots of loops. A universal loop (always on when the pedal is on), a boost loop (only on when boost is on) and last but not least a bypass...

Screen Shot 2023-10-29 at 16.13.37.png Screen Shot 2023-10-29 at 16.13.49.png Screen Shot 2023-10-29 at 16.13.56.png Screen Shot 2023-10-29 at 16.14.06.png Screen Shot 2023-10-29 at 16.14.16.png Screen Shot 2023-10-29 at 16.14.25.png Screen Shot 2023-10-29 at 16.14.35.png

seems to be rare, can't find much info about it...
I got this from a music shop cellar clean out, it's had a bit of schorching and smoke damage to the outer shell, although the plastic knobs and marshall type jacks are not...

Hi to all.
Maybe you, like me, have a lot of germanium pnp transistors that have a small beta (20-30)? And you don't know where to apply them? I have the same problems :)
And I thought that it is possible to apply them somewhere and found some solution. The essence of this solution is as follows: the first stage should be a silicon npn transistor to significantly amplify the signal and solve ground problems, then two stages on germanium pnp transistors, and then a silicon npn transistor...

A semi-original from Xotic... some RAT similarities, but plenty of differences compared to your average RAT clone.

Schematic:
xotic-sl-drive-trace-schematic.png

Full tracing journal here:

PCB available here:

Hello all just worked on a Doctor Q and got it running and ran into a rather weird deal with the circuit. I noticed when I use just the pedal by itself the “quack” doesn’t begin to occur until 10-11 o clock and even then you gotta attack the strings pretty hard. Seems as if the circuit wasn’t being driven hard enough for the range to do much as far as having a versatile range. Sure enough when I switch on the Alembic booster on my strat the effect seems to quack with ease at 10-11 o clock where...

So. Anyone has any information on this one? It seems to be a nice sounding overdrive.

I stumbled on a blog post with a few photos, but there's not much that can be done with those. Anything more than guessing.

I'll throw in my 2c with speculating about the JRC4558 having 1N4148s and Schottkys in the feedback loop. Gain pot at A50K could point the gain setting to be closer to Marshall Bluesbreaker than a TS. 5 transistors in all, could be two AMZ mini-boosts or any other muamp...

Intro

Hi everyone! I had the chance to get my hands on the MXR Doubleshot for a little while, and found out there are no available schematics anywhere. It's nice to do some selfless circuit tracing once in a while, in the true spirit of FSB.
Starting from what was known already, the Doubleshot is usually described as the dual channel version of the Dime, and we'll see this is accurate. That circuit already has something interesting in its own right, but this one builds upon it with the...

Trying to revive this thing. Actually trying to get one out of two going. Recapped the power supply and boards. Also swapped the starter cap for the motor. All electrolytics were reading at least double their proper values. Initially, I had a lot of motor noise mixed into the audio and no echo. Recapping seemed to have resolved those issues.

Problem now is the echo keeps dropping out and I get a lot of static. If I mess with the motor switch I can get the static to stop and eventually get the...

Hello I have a very noisy Deluxe Electric Mistress V1
This circuit :
I've modded it to this circuit (Deluxe V2) :
I thought it would help but it didn't.

I did a recap, a good calibration.
I've read a lot of things in this forum and I tried a lot of things. But there is still a lot of noise at the output. I even had a spare SAD1024 hanging around, I've swapped it and it didn't change a thing. I've also replaced the balance 1K trimmer.

Thank you for reading and for helping if you have any...

Hmm. Caline catalog is becoming quite puzzling one. These two here. Same f*king circuit. Paul Cochrane Timmy. 4558D, no switch for clipping, just the four 4148s for both. Highway Man has linear and log pots for bass/treble and Pure Sky has them at C50K. Pure Sky has designation screen prints under the components, but just by looking at the boards, component values and topology, i can safely say the circuits are identical.

Why on earth would anyone release two differently named pedals that have...

Hi guys, I am selling these tube amp pcbs:
1. Freeman BE100DLX based pcb (3mm thick pcb with 2 Oz copper) - 40$
2. S.I.R. 34/36 with plexi clean pcb (2mm thick pcb with 2 Oz copper) - 30$
3. Cameron CCV/Jose 50 based with simple clean pcb (2mm thick pcb with 2 Oz copper) - 30$
4. Fx loop - 8$
Flat shipping costs should be around 20$

Everything is verified and built few times
layout wirings are here

Cheers

Occasionally on ebay, now here the first time some guts:

analogguru

Hi all, I have a tc electronics t2 (digital reverb). It’s generating its own noise, when I change the reverb settings I can hear that it has an influence on the noise. I have audio traced the signal to the ak4556 ad da ic. The signal gets to there then seems to have the noise on pin 8. I’m wondering if this means the ic has blown? I can’t find schematics unfortunately. Thanks all

I have a Smart People Factory Greenline overdrive and it stopped working.
When connected and engaged it gives a lot of noise.

On the PCB I see one red power wire loose (see attachements at place W4 on the PCB).

Any idea how I will be able to find a resource to solve the problem please?

It didn't seem like anyone had attempted this one aside from the photos in this thread , so here you go.

Schematic:
keeley-compressor-plus-trace-schematic.png

Full tracing journal here:

PCB available here:

Just came out.

interested to see what TS-9 mods has been implemented?

Anyone had a chance to test it?

Seems it uses a PT2399 with Bontempo, according to the official website.