Hi..

Anyone know the maker or brand of Blue Axial Capacitor 10uf in landgraff & lovecraft using. It's not Phillip or BC Componet Brand. The body is slim than Phillip.

I have a few spare parts here i'm willing to trade for anything guitar related but at the bottom theres stuff im particularly looking for. Hope you find what you need!

a TL071, a few TL074s and TL072s
some CD4053 (tri-analog switching IC)
some CD4013 (CMOS IC)
spade terminals
few jacks from old guitars
crybaby clone circuit (minus the input jack, wah pot and switch)
LM386N-1 (power amp IC)
1N914/4148 diodes
common electrolytic capacitors
'snap off' componenet sockets
BC549C bipolar transistors...

Harbor Freight has a sale in case anyone needs a set.
MANUAL KNOCKOUT PUNCH KIT

Forged, machined and heat treated high carbon steel construction. Includes: 1/2'', 3/4'', 1'' and 1-1/4'' dies; 7/8'', 1-3/32'', 1-11/32'', and 1-11/16'' hole punches, driving screws and blow mold carrying case.

Capacity: up to 10 gauge mild steel, aluminum, fiberglass and plastic; Weight: 2.65 lbs.

About 12 dollars.

Everytime I go looking for the 1n34a diode I find 1n34's and no 1n34a's. NTE list it as part code: 110MP but all I ever find is NTE 109 which is a 1n34. What is the difference? and what is it a adequate substitue? Thanks in advance.

Two 125B enclosures drilled for a two knob pedal and one 1590 drilled for a three knob pedal and powder coated in Flat Black Wrinkle.
All enclosures are new and unused. Black enclosure's LED hole is slightly off center.

125B: $10.00 each shipped in the U.S.

1590: $13.00 shipped in the U.S.

Are there any workalike's or replacements for the SAD style chips?

This is slightly off topic but does anyone know of a purchasable enclosure that is similar to the one used for this fuzz or any of the wedge shaped fuzzes? Thanks a lot.

Fender stopped selling these about 2 years ago but I'm wondering if anyone knows where I might find one.

I've got several Colorsound Wah/Swells, Fuzz-wahs, etc that are in need of new dual pots to replace the scratchy originals. Does anyone know where I can get dual pots that will fit in these? Are the original style ones still being made?

Anyone run across a source for these? And yes, I know I could 'roll my own' but the forum is Part Sourcing.

As the Japanese manufacturers over here don't seem particularly bothered about vactrols and the like, their prices are fairly high I think (cheapest Ive found for a VTL5C3 is $6.50 each).

Any place worldwide that would be cheaper?

Hey guys... i'm not giving this enough love. In fact, i can't remember the last time i used it :oops:

can anyone use a powered breadboard?

$60 plus shipping

This is a BYOC (Build Your Own Clone) Ultimate Fuzz Pedal Based on the original Dallas Arbiter Fuzz Face with NPN AC127 Germanium Transistors.

Pedal is new and has about an hour of play time on it.

Pedal is very clean and neat inside.

Enclosure is Powder-Coated in Silver Metallic.

$70.00 shipped.

hi guys,
i have to change a faulty pot in a steinberger guitar, and can´t find ANY replacement that fits...maybe some of you guys have seen pots like this and know where to get them ?
this is how it looks:

the bushing is M7, the axle diameter is 6mm, the length of the whole shaft is 20mm.
it is a 25K log pot. the print on the underside reads T10A25K U .

anybody can shed a light on this ? i tried searching banzai, stewmac and tons of other distributors, but to no avail.

thanks in advance,...

Hey guys, I was just wondering, would you consider the caps, resistors, etc. from Radio Shack good quality or is it better to stick with Small Bear and Mouser?

Is there a source for the larger size (Phase 100)? I'd like to drill a hole in one for a power>battery snap connection.

I need a board of vero at least 9 strips X 23 holes to build a BOR.. Money order's are really hard to access in my area, so I was thinking sending maybe $5 straight up cash..

Let me know if you have extra strip board..

Hi , im looking where to find all the parts to build some stompboxes.
Im from belgium so radioshack is kinda a long trip to get a $1 transistor.
Theires a electronics shop nearby called gotron.

I was just wondering what parts id buy to get started.
This is where the questions kick in.
Which caps should i buy (axial radial ,.. )
which ones are -||- and which are -)|-
Does the voltage of the caps matter (most seem to be 16-63vdc )
I got a list of their transistors , pls let me know which ones...

I need 470k (log) and 1k (lin). Any of you guys have some you'd like to sell ?

I've found the SPDT at Small Bear, and Steve has NO momentarys. Anyone know where else I can find the SPDTs for cheaper? Also I can't find NC Momentary Footswitches switches.

Thanks.

I ordered a bunch of stuff march 11, but it hasn't been shipped. How long do they usually take? :whappen:

Is there a source for these - its for an older pedal - I assume they are the same (screw spacing etc)?

This meter is USED and has a few minor scuffs. I have 2 of these and this one has only been out of the box maybe a dozen times the scuffs appear to be from rubbing around in the box.

The meter comes with 2 test leads, 2 screw on alligator clips and the manual.

Couldn’t find the manual online so I scanned it ;)

Grrr… prices on the newer 9005A are 1/2 what this one cost new :x

I would rather trade it for a good analog volt / ohm meter. Other testing equipment considered.
Sale price $30.00...

They're doing end column pricing for 24 hours from 12:00 today. That means some bargains, e.g.

111X60X30MM DIECAST ALUMINIUM BOX (RC) 30-3650 one-off price is £2.88 (inc VAT), current price is £1.68.

LEDs from 3p etc

Unfortunately they're out of OFC professional instrument cable.