Looking for this square yellow output cap used on this FF board.

What brand is it?
Where to buy?

Looking for an LED mount to replace a broken one on my Sanox Super Analog Delay. Anybody know where I can find one like this?

I know these are super rare, but you never know so I thought I'd ask. After seeing Phil x do all those demos on youtube with his 213 or 250 tonemaster amp, I thought It would be cool to build one of those amps. The only info on the varistors in the vibrato circuit I could find was some part numbers, FR1039 and FS308 which were 1MA @ 68v and 1MA @ 110v silicon carbide varistors.

Does anyone have a few of these or know of a work-alike and where to get them? Thanks.

I want to get a small run of PCBs made and can only remember seeedstudio.. :slap:

Who else is out there?

I'm looking for a schematic custom audio amplifiers OD 100!

thanks in advance

vk

Looking for a vintage v3 enclosure. Let me know what you got.

Where do you get PCB mount switches that can mount flush alongside 9mm pots on the same board?

Anybody got one?

Please pm me.

Die-cast Aluminum Pedal Enclosures.
Professionally powder coated in Austin, TX

Dimensions: 5.7 x 4.7 x 1.5

Pre-Drilled for:
- Input / Output Jacks - DC Power Jack
- Potentiometers
- On / Off Switch
- LED
- Ground

Thanks for looking!

After some success with the 2SK117, I wanted to push my luck.
Obsolete JFETs are still on the menu, this time some (allegedly) Fairchild BF245A ( datasheet ).
ebay item link:
ebay seller xripley from Czech Republic:

From a batch of 25 pieces, tested with Peak DCA75.
Average Vgs(off) = -1.78V
Average Idss = 4.01mA
Standard deviation Vgs(off) = 0.25V
Standard deviation Idss = 0.76mA

Pinout is a match, with swappable source/drain.
Vgs(off) and Idss are both within datasheet spec.
Visually they...

Does anybody know where to get these knobs other than BYOC?
I'm looking for large color fluted mxr style knobs that measure 23mm in diameter. Specifically red, green, and yellow.
I'm aware of the large 25mm knobs that have rounded flutes - I'm not looking for these. I have them right now and they are too big.

This is what I'm looking for:

The only reason I'm trying to find another place is because BYOC charges a lot for shipping

This is probably an easy question, but the internet hasn't shaken loose an answer for me yet. I'm trying to find a replacement wiring harness for a GCB-95 Crybaby because the one in my modded pedal is not in the greatest shape and I'd like to clean up the crummy solder job in there. Does anyone know the correct replacement connector and/or have a link to this wiring harness for purchase?

Hi all,
Is there anyone here who'd be able to sell me a replacement P-2356 transistor for my 1967 BG-1 Boomerang? If anyone would have one, it would be one of you excellent guys. :thumbsup
My tech has determined that one of the original trannys needs to be replaced. (noisy)
Thanks a lot.
Sean. (Toronto)

I'm new at this, and I certainly do not claim to know all of the nuances of the game, but I seem to be having a devil of a time finding 16mm audio taper pots (right angle PCB mount). I'm in the U.S., and I've looked on all of the major sources that I know of so far: Mouser, Digikey, Small bear, Love My Switches, etc., but no luck. Linear and Reverse Log seem to be everywhere, but not audio taper. Is there something in the terminology that I'm missing or some other spec necessary to find what...

hi, where can I get these pots or similar, that have long shaft, in usa?

like this:

Hi,

I got these recently from a friend. He said these were DIP14 741 opamps. Somewhat unusual but according to datasheets not impossible. Is this so and which company manufactured them (I can't read that logo)?

741P.jpg

Hey all,

Trying to repair the faulty rotary encoder pot on my Boss DD20. The sweep in either direction is glitching the delay time like hell. Had a similar problem with an older WH-4 Whammy, but sourcing that replacement pot was a breeze. I've found the part number, but nothing else. Contacted Boss/Roland and they're giving me the run around. If anyone has a line on this rotary encoder I'd greatly appreciate it,

Part# 03231912 ROTARY ENCODER W/SW R-ENCODER EVQB1SZ1720B

I understand the...

I have to say that this surprised me as well! I recently bought 10 x MN3207 for £6.81p (for delay/chorus/echo units) and 50 x BF244B for £13.13p (for a 3-notch Phaser). I did some digging around Amazon, and I found some real bargains, such as 50 x LM13700 for £30.39p, which is less than 61p each. Farnell and Digikey sell them for about £2 each! Amazon also sell PT2399.
I don't know what electronic components appear on Amazon outside the U.K. nor their cost, but it could be worthwhile having a...

Just thought I'd throw this out there, I rolled the dice on these K117, fully expecting fakes.
I tested half of them (25 out of 50) with a Peak DCA75.

Average Vgs(off) = -0.351V
Average Idss = 1.815mA
Standard deviation Vgs(off) = 0.023V
Standard deviation Idss = 0.262mA

Pinout is a match, and obviously they come up N-channel with swappable drain/source in the DCA75.
I tried a couple in both a SS/BS mini clone and a Duende boost with no noticeable change in circuit self noise vs. SMD J201....

I'm looking for the following Panasonic capacitors, trying to build as accurate of a Klon as possible. If anyone knows who may still have any stock, or if you've got stock of the capacitors below please let me know. Thank you!

100n ECQ Series Film Type
4u7 Panasonic SU Series Electro. 50v.
100n ECQ Series Film Type
68n ECQ Series Film Type
68n ECQ Series Film Type
390n ECQ Series Film Type
82n ECQ Series Film Type
390p ECQ Series Film Type
1u Panasonic SU Series Electro. 50v.
1u Panasonic SU...

With smallbear down, I'm wondering where you guys would go to source parts like certain specific trannies, Jfets, and other parts. Since you can't trust the authenticity of these parts buying from eBay sellers or even Tayda.. Does anyone have suggestions for suppliers (I'm in the US) so I can get soldering again?? I Appreciate it guys, thanks in advance.. And stay safe and healthy out there everyone!! :D :D

Does anybody know where I can source a replacement pot of a Boss pedal? Specifically, a 9mm right-angle Alpha-style 250k reverse audio pot with a split shaft.

Hi guys, I’m currently hunting for some 2g381s for a tone bender MKI build for purchase or trade. I have some ac128s, 2g374s, OC81Ds, OC81, OC75, OC71, AC176k, NKT12 and various Russian germs id be happy to trade. I just lost my job to coronavirus so can’t really be affording the insane prices on eBay at the moment.

Hope you all are keeping well!

Tom

Hi,

I've just bought a Dunlop EJF1 Fuzz Face and I'd like to increase the output volume by upping the 330 ohm resistor a bit.
I do not however want to change the look of the nice old school circuit board by adding another type of resistor, so I'm wondering if anyone knows what type of resistors that are being used in this pedal?

I can't attach pics to this post but the resistors can be seen here:

Nice sounding fuzz!