I can get hold of about 50pcs or so genuine MN3007
I am in the UK, they will be £10 plus postage to your country.
Anyone interested shoot me a message

I need to replace this pot in a Lovepedal Purple Plexi with an audio pot. I'm not having much luck finding an exact replacement style. Anyone got any suggestions?

IMG_20200411_160828322_HDR.jpg

Hello

Anyone have a source for a transformer for a JMP-1 preamp?
I may have to rebuild if I cannot find. In case I need to rebuild, anyone know what the HT voltage is supposed to be? Based on schematic the LT secondary appears to be 12V then there is a 15V center tapped also but it doesn't say what the HT secondary voltage is.

Any info would be appreciated.

Thanks
20200328_151553_resized2.jpg
20200328_151600_resized2.jpg
20200328_151609_resized2.jpg
xformer.jpg

Picked up a DC-2 project board from another memebrr. Having a hell of a time finding DPDT pushbutton switches with silver retangular switch caps that look like the originals. Any help is grratly appreciated! Trying to restore it to oem.

Looking for a couple of real LM308s. I'm in Ontario, Canada, I'd pay for letter mail and whatever you decide is a fair price.

Hi !

I just fixed a Danelectro Cool Cat Transparent Overdrive V2 (opamp was dead) and when I put it back together I broke the 3pdt switch.
I've been searching for a similar one online but I can't manage to find it. Here are some pictures :

It's about the same width and length as you usual 3PDT, same solder pins spacing, but way lower (about 31mm).
I tried emailing danelectro but they won't give me any info, and I did try some other small sitched a try (like this one but they don't match....

Hello everyone, I'm Tom.

I want to build my first pedal next week and I'm going to be making a Catalinbread SFT II as the title suggests. This is the schematic I'm using. . I found most of the parts here in the Netherlands for the build but I can't find the mpf4393's anywhere. Now I want to use a different transistor but I have no idea what transistor would work since I read about a lot of people getting oscillations with some transistors. The store that I want to buy the parts from has quite...

Sort of a long shot, but seeing if anybody has a spare Ghost Effects Lunar Incantation PCB they could sell? I got ahold of Ian at Ghost and he doesn’t have any left.

Does anyone know where I can find barrel-style negative tip 2.1 DC jacks for a .6 inch / 15mm hole?

I'm looking for a replacement slide potentiometer for my black (recent) MXR Ten Band EQ.

Dunlop has the sliders for the black M108 Ten Band EQ on their website, but you can't buy them directly from Dunlop:

Part nr: ECB046

Ordering them directly from Dunlop is not possible, they emailed me.
Dunlop refers me to a distributor in Antwerp Belgium AB Music (algambenelux.be) but they also do not sell to end users.

The sliders (probably) are:
Taiwan Alpha RA2545F 20k LIN RED LED
See:...

Hi All,

I am looking for 2N270, 2N2613 and 2N408 to build a Fuzzrite and a Maestro. I have a few 2G381, Mullard OC44, OC71, OC81D, OC76, SFT337, SFT363, NKT213, AC125, AC128 etc. to trade if any one is interested.

Many thanks.

Hello guys,

We are working on designing and building a chorus pedal. We are finalising our PCB pedal, and we are looking into the enclosure.
We have little idea on how to deal with the enclosure so if anyone could help us that would be wonderful!
Some key questions we have are:

-Which companies manufacture a pedal enclosure?
-Can they be tailored enclosures? or they have to be relatively standard?
- Is the manufacturing process something we should look into?
- Any idea of the cost?...

Short version: Don't step on the knobs of Strymon pedals! The pot might break!

I bought a Strymon BlueSky pedal that had the Mix knob turning freely through all 360°, which is bad. Only the normal range of the pot gave sound. If the pot was turned into the range it doesn't normally go to, the sound cut out.
It was obvious the pot was broken, so I fixed it by replacing the pot with a strymon replacement.

I've read that other people have had this problem with Strymon pedals, so I figured I'd...

Hi all,

i have a vintage Colorosund overdriver pedal, which is great and in perfect condition. But it has scratchy pots all over the place. I was about to order some DeOxit D5 (being in Europe this is not that simple as it turns out, especially due to the shipping constraints). But then, after my order was canceled due to inability to ship it par avion, i read more into it. I found numerous reports stating that there are types of DeOxit that are not a good fit for potentiometers (D5, which...

Hello everybody, some time ago I purchased this 1590DD copy enclosure on musikding, for the evenience of a big project

It cames with 6 screws in a blister, inside the box, but I've lost those damned screws! :slap:

I've tested various other screws form standard 1590B and BB boxes (both Hammond and Eddystone), but none of them fit. For sure the standard 6-32 x 1/2 for the original Hammond 1590DD not fit. The seller has no spares for this enclosure. Someone here knows the scres needed?

Hi, I'm sourcing parts for my diy fuzz face and I would like to know if there's anyone here that has ordered the so claimed Fuzz Face Classic Si Transistor Set and has measured their gain, just to have a reference point to what I'm looking for. I know that the Q2 should have higher gain than the Q1, but I don't have exact values. Any help would be greatly appreciated.

hello,

I have, too, read countless posts everywhere about the fake transistors and ICs that we will get when we go so low as to buy from ebay...
and of course, it is clear that those warnings are well-intentioned... not to mention that buying fakes does happen, for real...

at the same time, my waiting period is over, cause my ordered transistors have arrived,
and I've just built a circuit of a jfet, 2N5952, which I bought from ebay, and it works flawless, and I'm very happy...

by making...

Thousands of capacitors for sale. Bought a huge lot of NOS caps. I will never use them all so I thought some of you folks could use them. PM me for more details.

-Tim

This is brewing up at the other place, thought some of you guys might be interested. I plan to make a double-sided layout for the Gristleizer. The details are a bit up in the air. So far it seems people do not want board-mounted pots or rotary, in order to keep the size of the PCB down a bit. Personally, I prefer them, because I hate offboard wiring, but I'm not even sure I'm going to build one, so I'd rather make it the way everyone else wants it. The board will have silkscreen and...

Hey all,

about to start building a Phase 90. Was doing some research and from what I saw the type of JFET used to Bias the Op amp phase shifters doesn't matter as long as they're matched (correct me if I am wrong on this). I normally try to use SMD JFETs in most of my builds (MMBFJ201 or MMBF5457) just because they are easier to get a hold of. I have also heard that SMD JFETS have significantly better Tolerances and don't necessarily need to be Matched? Anyone confirm this?

Thanks,

Hi all, looking for a Scott Schwartz AD3208 pcb. GGG no longer stock it and I was hoping someone here has one for sale. I'm located in Australia, so hope that post is manageable from your country. Cheers!

I have part of a Schematic for an ADA cab sim and there are two caps, C4 & C5, with the same value u1J163 . All other caps are standard, ie 10uF.

Can anyone tell me what u1J163 is?
cab-type-speaker-size.jpg
Thank you

Hi everyone,

I'm selling out some old stuff on ebay that I don't need. There are some nice nos germanium transistors and some old capacitors.
ac137, ac139, ac128, ac127 and a very nice oc604! if you're interested take a look at:

thank you!

These are off an old Korean Bass onboard pre that's past it's best.

But they would be handy for mounting the new pots if I could find them in the right thread. Anyone seen anything similar? I'm drawing blanks everywhere.

TIA.