Right... i'm after a few PCBs etched up from DIY Layout Creator Layouts and some parts in Exchange for any of this stuff -

1 x Dallas Rangemaster PCB
1 x NOS Full Legged Metal Can NKTOC44
1 x TonePad Tone Bender MkII PCB
1 x OPA2134PA Dual Op-Amp - New
1 x MAX1044 - New
1 x MAX1771 - New
1 x HPro PS200R Power Supply - Good as New
2 x Vintage RCA741 Op-Amps - Desoldered
5 x NPN BCE Pin Out 70s Silicon Transistors - Snipped (Have a few sets)
5 x PNP BCE Pin Out 70s Silicon Transistors -...

Up for sell just an enclosure, no board, as I used it already, but I'll trow into the pack large sheet of 2mm NOS pertinax, so with the layout in the supafuzz tread you can make your own. Also 2 large style Marshall type knobs are included.

Shipping preferably inside of Europe, US shipping is way to expensive.

Possible trade for two Prism I, or YY pedalenclosure.com boxes

Price $50 shipped. I've paid $70 + shipping few months ago :roll:

I'm located in Poland

Cheers
Pawel

So, on a whim I bought 10 NPN germaniums off ebay. The price was dirt cheap, so I figured I would risk them being usable. However, I'm now having trouble finding the formal data sheet for them, and I'm questioning the pinout.

It looks like the middle leg attaches directly to the case which makes me think that is the emitter, but most Ge devices I've always seen the emitter on one of the outside legs. On the other hand, the Si transistors in my Acoustic 360 are arranged with the emitter in the...

I am needing a 200 Volt 15 or 20 amp mosfet any ideas all of my Google searches will show me so much info but when i get to the datasheets its not what i asked for. that and they will show me a 150v 10 amp mosfet and say it can only dissipate 180watts of energy. what kind of backwards math is this? does ohms law not work anymore?

anyway i would appreciate help from anyone
thanks

ed

looking for .003uf and .005uf, about 5 of each. just for stompbox use, so high voltage isn't too important...

Smallbear don't stock anything that large, mousers minimum order/shipping is way too expensive.

any other sources, or anyone got some to sell - i'm in New Zealand, but international shipping shouldn't be too bad.

Cheers,

Jeremy

I've got one of the older Memory Man units (1xMN3005, 1xCD4047BCN, 1xNE5554N, 2xRC4558, 1xMC1458) and I'm looking to find a replacement DELAY pot. It's a 24mm 1M Rev Audio with right-angle PC pins. I'd be very OK with a pot with solder terms, but I can't even find one of those! Any help would be a big help! Thanks.

If someone got big selection with good variety of all kind of 8-pin op-amps useless, I'm intrested in buying them. They can be new or used, as long as they work and the price is affordable.

Mostly looking for a batch which includes at least 20 different type of em

Also if someone got a big amount of just 741, intrested in them too.

Hi All,
Well I have gone through the last of my stash!!! :D
Here we have : 5) MXR analog delay (green,a/c powered) boards
these are in great condition!!! only 5 to sell!!!!
1) MXR COMMAND series phaser board...in great shape
25+) MXR stereo chorus boards (yellow, a/c powered)
The chorus and the delay boards are from 1980. the phaser board is from the mid 80's.
I HAVE NO DOCUMENTATION FOR THESE!!!! NOTHING 0 you are on your own......
I would like to get $15.00 for the phaser
$25.00 for the delay...

Hi everyone
I have acquired in a swap around 8 Snarling Dogs wahs, which need attention. The list proce on these is £100 plus. Will be letting them go for any sensible offers, to clear stock. Or swaps ? Theyr'e bloody solid pieces of metal and would make great enclosures for any wah builds, either they're fixable or use as a case and scavenge the parts! All true bypass!

Hi everybody, I've triyed to add my questione to the cheap oscilloscope tread by Modman but I can't post on it...
so here's my question, I've found a peakctech 4020 for 70 euro, is it any good? does it worth the money?
thanks in advance

Hi everyone i bought a 5 watt valve amp kit from ampmaker.com. I bought the timesaver without valves £135, and upgraded the panels to gold plexi (£12). I also ordered a custom made head cabinet (£95) on the website. But..
I've just picked up a beautiful 18 watt tmb clone, which will suit my needs better , so don't have the funds or time now. Up for offers?

Hello
I'm looking for a replacement for the Mn3011, anyone knows any?

Greetings

Can't find them just about anywhere. I ordered some from Futurlec, but they ended up being out of stock with no expected stock date. I have EVERY other value I need, but for the life of me can't find 0.39μf.

Any recommendations?

Thanks again!

---
Cam

Hi Fellow Freestompboxes,

Does anyone know where I could source some ME9002 Switching Transistors or some nearest equivalents?,thanks in advance... :)

Just used an SAD1024A in a repair and I need to replace my stock. Anyone got a verified working one for sale?

anyone have any suplus stations or irons for sale? In the UK?

Hi all. I'm new to the board and I seek knowledge! :D

Well I love old BC108C fuzz faces, but don't really have the money to buy one. So I'll try to make one myself as best as I can.
I know there used to be Philips BC108C's in the fuzzez marked as TFK. I can't find those transistors anywhere. The CDIL BC108C's are easy to come by.
Can anyone tell me what the tonal differences are between these?

Any input is very much appreciated.

Thx!

Radio Shack has these little LED assemblies that are one single unit with current limiting resistor build in. They seem like a wonderfully solid idea to me, and they look cool to boot. The problem here is two-fold: they are $1.99 a piece, and I dont necessarily trust the quality of RShack products. So.....does anyone know anyone ELSE who makes a similar LED assembly?

Here's the Rshack one:

Does anybody have those? AFAIK it's British diode. I need 10pcs. I Can offer your asking price :thumbsup

Cheers
Pawel

Off topic: Would someone be so kind as to point me in the direction of the AC adapter jack used in the pedal above? These internal nut ones I've been using are starting to annoy me...

Thanks in advance!

Hi Guys,

I am building a CE2 clone - I bought a set of MN3007/MN3101 of ebay, and I appear to have gotten burned. the seller had good feedback, but i'm pretty sure the chips are fakes. If anyone has a genuine set of chips, at a reasonable price, let me know :D

I would go through smallbear, but they are currently out of the mn3101, and I would prefer to get a set together...

Cheers,

jeremy

Ended up with one of these buy mistake!

anyone interested!??? Need to make space!

Hi,

anyone know of good place in Australia with a decent range of pots with solder lugs . All I can seem to find are PCB mount.

I'm looking for B100K dual gang amongst others.

Thanks in advance,
Dave