Has anyone seen and/or built this? I have built a few of them and it's a really useful circuit IMO.

Hi
A question
This scheme has no input and output buffers, which are desirable for preserving the tone.
Tell me, how are things at this pedal with input and output impedances?
What are their sizes
Does it make sense to add buffers or input impedance is 1 megohm and the output does not exceed 50 kilo ohms
c25844Marvel cctedb238.png

Just as interesting about these schemes
kejina.png

In the effect pedals it is recommended to create circuits with a high input resistance around megohms
And a...

hello,
so... I'm not sure on the ethical aspects of my post so If I transgress I trust I'll be told.

Over at diystompboxes there is a schem that 'cynicalman' created using two pt2399 to make a pseudo-dimension c.

I've wanted to try a dimension c for quite a while and the two layouts I have seen, as far as I know, are not only complicated as heck but perhaps prone to issues (ticking?). With that in mind this schem appeals to me.

I've tried to setup a user over there... but had issues.

I've...

cue fog machines, cue twilight zone music, he's back again with yet another stupid episode of how to mutilate your beautiful expensive guitar's sound, and obiterate the effect of them beautiful expensive toneful tubes.. :mrgreen: :popcorn: :popcorn: :popcorn: :popcorn:

SUBmitted for your approval or disproval in which case i don't care so go away and soak thy head in a bog or something.... :shock:

here's uncle ed's overdriver. my partner-in- crime in the luthier thing asked me if i could...

Hi Folks,

I have a question about the purpose of the 3.3M resistor (R5) in the boost section of the LaVache pedal from Madbeans. Its a variant of the Lovepedal Les Lius Overdrive which I believe is built upon the Electradistortion.

Here is the schematic

When the switch is open its just a huge resistor in parallel with R4 and when the switch is closed its bypassed completely.

What am I missing!?

Thanks!

,,,,,suck, model b... the more standard fuzzface... but si instead of ge...

the full-gospel si fuzzface. mods detailed. output pot 100k, output cap .047uF
e to ground q1, 220r e to top of fuzz pot q2, 47r, 100r between fuzz pot and ground

fat and philthy, and cleans up just like the ge ones and responds pretty much the same as well. couple extra parts and huge diff.

any npn's will work. i use 'em around 215hFE/.650ma

if ya use say, 450hfe, double up the e resistors. you'll have to play with...

Hi List,

Introducing my new electronic project,
It's a Hammond scanner Chorus/Vibrato guitar effect
using its original vibrato line and a bunch of electronics
to support it. All this put inside a small cabinet
stolen from a scrap 15w guitar amp.

You can hear it on this youtube link:

You can also have a look at a group of detailed pictures
showing most of the steps involved in the building process here:

It's a one year project I'm proud of.
Cheers !

J-Pierre
Quebec City, Canada

I have finished the re-design of this platform to make it more of a regular DIY build. I based it on the Ursa Minor

but the basic idea is applicable to anything that will fit on a 60mm x 60mm piece of perf or PCB. You can build inexpensively and still have the no stomped pots benefit of the enclosure. A full kit is available

as well as individual parts for those who want to roll-their-own.

Please recommend the Ursa Minor to first-time builders who want a carefully-thought-out and...

I know from e-mail feedback that many people worldwide have used my tutorial to set up this hot-rodded Electra clone. I have re-worked the kit that I offer for it and the tutorial to make the kit more economical and to improve the instructions. You wind up with this:

It goes together in an hour or less, the tutorial teaches good layout habits and the resulting tone is professionally usable. If you go for my kit, you get an NPN germanium transistor and a '60s-vintage dot that are...

From a small DIY guitar electronics book which I bought
in the mid-1980s.

I remember building this for a friend at that time.

I think it sounded halfway between an overdrive and distortion.

The circuit obviously has to be modified to be of use in practice.

I think R6 can be replaced with a 500k variable resistor as
a Distortion control.

Another variable resistor will have to be added as a Level control,
I guess at the output after C5, or after Pin 7 of IC1.

A tone control circuit could...

This one is semi-DIY.

I call this my Fanta Fuzz...because the orange knobs remind me of Orange Fanta.

I started with a BYOC Lil' Fuzz kit, which suddenly has been deleted from the BYOC website.

I made a couple of changes to the stock Lil' Fuzz:
I always run my Gain/Fuzz knob on max so I hard wired the Fuzz to maximum (2k resistor) and removed the Fuzz pot.
I like having access to the BIAS pot so I installed an Alpha 25k pot for added flexibility.
The stock 2.2uF input capacitor is too bassy...

Hi,

A simple tremolo circuit. Vintage 1980 I guess, eastern europe. Basic components

Hi,

I just thought someone might be interested. An echo kit built on MN3207. Advertised to be built used with a mix in the effect loop I guess.

Cheers 8)

Hi guys,

I've seen a DIY project with an active BMP tone control which seems pretty cool as you save one gain stage because it's placed in the feedback loop.
So there is no need for a recovery stage respectively a buffer.
Guess this could be very interesting for a view pedal builders..

I like the BMP tonestack a lot but would like to add the Body control of the AMZ Presence Control to alter the mids.
Not sure about the values,what a pity I'm not into spice.. :(
Just imagine what a killer tone...

Hi folks,

Here's a new DIY project release from me - the Subspace Transmission Fuzz.
It's a fuzz with a recording and playback feature based on the ISD1820 voice recording chip.
It can record up to 20 seconds and the playback can be repeated and pitched up or down.
It's a pedal you can have alot of fun with... :)

It's an easy build that doesn't require any programmable chips.

More info in my blog at

I hope you like it
Cheers, Fredrik

Hey guys,

Just finished to bread-board the full tube / high-voltage tremolo and it sounds like this (very happy with the result i might say).
The schematic was modified and an updated schematic will be available soon. If you like to jump directly to action you can go to min. 2:13 but if you like to hear the explanations you can listen to the whole clip.

Schematic (the one on the clip was modified):

Video:

Regards,
DeX

Hi folks,
Here's a new DIY project - the Sentient Machine.

It's a LFO modulated resonant lowpass filter with two voices, a standard wah sound and a vowel sound.
At slow speed it makes a cool phaser'ish spacey sweeping sound aswell.

More info, PCB and schematic in my blog at www.parasitstudio.se

I hope you like it :)
cheers / Fredrik

Hello guys,
I'm working right now on a small system that will allow you to control a standard potentiometer using either MIDI or Expresion pedals. There is a lot of things to work on but i will present you the concept.
The idea behind this was simple: a electro-mechanical module that can be used virtually on any guitar amplifier to control various functions (potentiometers) and also preset storing (MIDI CC messages will be used). Also another requirement was this: anyone with a screwdriver...

Nothing fancy here too, it's just a TS-like design with tons of controls:
- Active mid boost/cut.
- Symmetric/asymmetric clipping.
- Choice of 4x different clippers.
- Tons of gain.
- Hard/soft mode.
- More switch with internal trimpots to boost volume and/or gain.

The presentation on my website

Quick example of how it sounds:

And this is the latest schematic :
Schematic_Zorgverdrive_Deluxe.pdf

Explanations are here:
In French:
In English:

A document with how to mount it from my...

Not verified yet but I think it should be without errors.

I found the tone stack non standard so checked and it is the same (except for minor differences in pot values) to the one displayed here: . The mu-amp (last stage) is the same (except for minor differences in cap values) to the OLC Orange Peel.

I've attached the eagle schematic file in the zip. Let me know if anyone spots any errors.

Had a little time to almost finish another tube project, this time we are talking about a modified version of the Alembic F2B preamp (you can till build the original version on the same board, as the modification we are talking about is just a buffered output).
I will post all the build documents soon, but you will have to keep in mind that the PCB is double sided. The heart of this is represented by my version of SMPS (the one that i'm using in all my tube projects).

Until then some sneak and...

Hi all, this is a simplistic noisegate that was published in the 80's in the dutch electronics magazine 'Elex', which was a subsidiary/small brother to Elektuur (which was the dutch version of Elektor magazine). Their projects were simple and aimed at beginners. All volumes have been released on CD and you can probably find it online somewhere.

I built this noisegate on a piece of perfboard in the early 90s and it performed 'ok', for what I recall.

Just today, I've put the schematic in...

I have just completed a Rockett Blue Note OD. I followed this layout:

I wonder about the fat -control. It should be a reverse 25K log pot but I couldn't find any so I used a normal 25K log, because people in the comment field said that would work. But when I turn the knob, I really can't hear any change.
I have also tried to solder it opposite i e the wire marked Fat 3 to lug #1 and the wire marked Fat 1&2 to lugs 2 and 3. But still nothing happens when I turn the knob.

The pedal works...