hello folks, i found this schematic on the web for the Aguilar OBP3 preamp, i want to use B100k pots for the eq but i don´t know exactly which resistors and capacitors i need to scale, as you can see is not the classic baxandall topology, could someone guide me please? thanks in advance
I'm looking for help on a specific split humbucker wiring. I have experience building and modifying guitars, but I've always used a pickup diagram. I've searched on all of the common guitar wiring diagram sites and several forums, to little avail. I am converting an SSS stratocaster to HH. I would like to keep the three stratocaster pots, having a master volume, tone for the neck pickup, and tone for the bridge pickup. The pickup combinations I'm looking to wire are as follows:
Hi guys... my Blackmor-ish sound search continues... After the TP-1011 preamp, now is the time of MTC, a circuit built by the guitar tech of Ritchie:
This circuit seems to be a LCR filter which helps to obtain the famous shaped RB sound... according to Dawk's site it smoothes up the sound a lot, it's some kind of subtle but still very noticeable. Your sound also gets crystal clear! With the MTC your tone pots stat to work like wah wahs, turn them to zero and it sounds like a closed wah but...
I hope it's alright if I ask here, I'm not a member of many forums. I asked this question on Talkbass as well.
I'm making a quad pickup, so I need to make 4 individual one string/magnet pickups. Should I still be aiming for a 7k-10k resistance range? Or does it differ if I'm using a smaller magnet. I did a test run and don't see me going past 4k rotations around the magnet before I run out of space. Some info:
does anybody have the baja schematic for active pickups??, id would like to try it but i have seen many different sch everywhere, so im looking for it in here, if BAJA can tell me will be amazing, looking for the EMG81, also if anybody have the LM4250 on smd eagle library its welcome too
Anybody have a schematic for the booster circuit found in 80s BC Rich guitars and basses or maybe someone has a BC Rich that can post some pics? Need to build one to replace the missing circuit in my 80s Fernandes Eagle copy.
Hi!
i bought an used Mike Pope Flexcore and i want to obtain the schematic in order to simulate it via spice and see the frequency response. Here it is some high quality photos, i've already traced it (red=upper layer, blue=bottom layer) and i tried using fiverr for the EQ section , the pcb where is located the quad-opamp (there is an error in the fiverr schematic: seeing the 6 holes the guy thought of a stereo pot but in reality the EQ pcb is used either with the bass control or a concentric...
Hi folks
First thanks to pf_fan for his encouragement and pictures, and a special thanks to the nice person on the EMG forum for providing some nice hi-res pictures of an SPC and EXG circuit board.
Now to the nitty gritty :wink:
EMG produce a range of active tone controls, but the most popular configuration is that used by david gilmour in his red strat - the DG20.
The most recent version is completely solderless with push on connectors and all the componentry is hidden between the rear of the...
Simple low battery indicator for usage in a bass guitar with active pickups. LED lights up when battery voltage is below 7V, indicating that it's time to change the battery,
Like the F1x, was browsing and recalled that I actually bought the schematic for the Alembic onboard dual filter preamp (older version of the series onboard electronics, I think).
I'll post it here for posterity.
Quite elaborate, these basses have two pickups and a dummy coil, which needs to be carefully adjusted. They also have a second order low pass filter per pickup, with either a switch or a pot for Q . In the old days, they used a separate outboard power supply, not sure if that is still...
Quick question; got a bass with 2 pickups. Each pickup goes to it's own active pre-amp and then to it's own output (a 5 pin output (audio left, audio right, ground, V+, V-)). Pickup > Pre Amp> volume > output.
I'm having an issue where I'm hearing the bridge when I'm plugged into the jack that should just be the neck, or vice verse. What can I do to fix that? Would a big resistor by the input or output help?
Hi, I found a cheap passive stingray bass copy and I build a simple pre amp with spare part I already own, I could have build the OG pre but I do not own a low current opamp and in my country is not easy to get reverse log pots. So I put a Tillman in the input, followed by a scaled james tonestack and a lpb1 boost as recovery, it sound pretty good for a fast and simple point to point build. Some problem, flat is not in the 50%, 50% position is more like in the 50%, 60%.
I've got a 5 string Stingray Piezo and now trying to replace its onboard preamp (want to swap it with Darkglass Tone Capsule - as for me, it works with more sweet frequencies). I don't need piezo and actually don't like how it sounds, so I just cut it off.
Since SR5 pickup has dummy coil, its wiring varies from traditional humbucker and proprietary ErnieBall switch with 15 pins is used in SR5s.
Just wondering if anyone has schematic of wiring such pickup with ability to switch coil...
I’m planning a guitar build and trying to figure out the electronics wiring. I don’t fully understand switches, whether to us a DPDT or a 3PDT on/on/on.
Then a separate mini-toggle: up - middle pickup only (shuts neck & bridge off). Middle - uses only the 3 way blade, for just neck/bridge options. Down - middle brought in with the neck/bridge.
But...however, I have made a copy that works fine.
875276590348dd41b40c61e691ca565.jpg b7926fa2e2d80863e8cb8cec6c519f5.jpg
63f5549eaed2fadf4ffd520a69f18a7.jpg 8d160049f2afacbc94714173bf45e65.jpg
————————————————————————————————————————
The progress of the reverse engineering will be updated again after a while...
60163d4eae5a0b96788345b085ccf34.jpg
Here it is... I opened one up for a local shop. A guy had his painted (!!!) and the painter hacked his wiring up, shoved it into the control cavity and gave it back to him. Duh, my guitar doesn't work. So the lack of available schematics etc. made this one a little more than your average rewire. The little board on the back of the varitone pot has all the connections labeled though, so tada, here it is kinda half wiring half schematic.
right click on the image for full view:
Need help finding a proper switch sourcing info.
And clear wiring diagram.
It seems there is a need to connect to the 2 poles to have the inductor connected properly.
help!
I'm one of those guitarists who does not live without volume and tone controls, I am used to set my amp with more highs and cut this excess in the tone control, when I want my guitar more expressive I turn the tone a little way up as a result it works as a second volume control that avoids gain losses.
Strat control tone works ok, but they are effective after 5 and its a little aggressive at the begnining (3 to 0), this circuit I have implement in one of my strats in the bridge...
I recently had the pleasure of repairing the preamp on a 1977 Ovation Country Artist 1624-4. The primary complaint was that the guitar did not work when plugged in. To make a long story short, after audio probing through the circuit, I first determined the electrolytic caps were dead, followed by determination that the JFET was dead as well. After replacing the electros (C3 & C4) and tranny (didn't have a 2N5459 handy, but used a 2N5458 with great results), it sounded very nice.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum