I am rehousing a Danelectro french toast fuzz (Foxx TM) and added an led via switching ground off terminal 13 of the 4013 chip, works fine except the LED is flipped, when I turn off the effect the LED comes on. I suspect this comes down to the switch I used:

While I've used this switch in the past on other relay-based pedals, this one is obviously not working. On another Denelectro rehouse I did I used this switch:

That one worked fine but the circuit already had an LED built in. I'm...

Hi!

My Zonk Machine started oscillating/squealing and producing static noise when attacking the strings. I didn't use the pedal for a while and wanted to put it on my board again.

The squealing is even heard when the pedal is off. The battery is new and works fine in other Tone Bender style pedals.

I made a short video of the issue:

Any ideas what could be causing this issue and how to fix it?

Thanks!

Hello! I'm working on finishing my first build and I've got the effect so close to working perfectly but I've run into this one issue that I can't seem to figure out and was hoping someone on here could point me in the right direction!

The issue is that when I switch the pedal on, the signal fades in from silence over about a second (which is a long time, I know). The interesting part, and where I'm having an issue figuring out what's going on is that this doesn't happen all the time. The...

I have a circuit which, with 9V, draws around 31mA. I've been using this voltage 'doubler' (image attached) with a NE555P chip to bring the voltage to 15.9V and the current to 75.5mA.
It sounds fine, no issues I can detect, but I don't have much experience using doublers so I'm curious if this looks like a good circuit to consistently use with that amount of current.
I'd likely use an SMD version of a 555 chip based upon availability.
Thanks in advance!

I was having issues with a parallel looper design and asked for advice a while back to help eliminate switch popping and circuit noise. The attached file shows a pop-free version; the switch popping finally disappeared after removing all pulldown resistors. The guitar signal was too quiet, though, and the circuit had a high noise floor. Although the schematic doesn't show it, I was using a voltage doubler.
The second file was a redesign using lower noise op amps and other changes. The...

Hey, I'm working on building a D&S II clone and noticed something I'd like to fix. I have the schematic below, I actually own a real one of these and the original does the same thing. When the gain pot is maxed the circuit gets super trebly, but if you back off just a bit, say 5% from max gain the circuit goes back to normal, the sacrifice is you lose some of the distortion of course. I'd love to understand why it does this first, then maybe someone could help me with a possible solution,...

Hello,
I recently made a board containing a Keeley moded blues driver and a blues breaker. THe blues driver works fine, however, the blues breaker I am having issues with. I get signal up until pin 1 of the op-amp, then I get nothing. I am pretty sure it is not an op-amp problem because I have switched it out for many other TLO72s and I get the same problem every time. I have built two boards and I am getting the same problem on both boards, so I believe it to be a board problem. I got the...

Hello! I’ve just finished the Jext telex white pedal using the layout over at tagboard effects.. I’ve quadruple checked everything and it all looks good.. however there’s no signal. .. main change was replacing the 220r under Q4 with a jumper (this was recommended to prevent oscillation late in the gain sweep). Other difference is I added an extra cut and jumper simply to accomodate the inductor. I tried turning the bc548 transistors the other way round .. no change. Double checked pinouts...

I’ve been dinking around on a fuzz face on a breadboard for a few days now. I’ve got it pretty dialed as to how I want it at this point. One problem though no matter what I’ve done doesn’t seem to change. When I use my strat (stock 2020 players) if I turn the volume knob below about 8 I have no sound unless I have the fuzz turned all the way up (I initially was following the directions from small bear that says use a 1k anti log so this makes the turn it all the way up even worse I think, I...

I recently built a Cephid chorus from PedalPCB (CE-2 clone). Works great and all component values were tested before building to make sure everything was in spec. I compared it to a Danelectro Cool Cat 18v (cs-505 clone) and the cool cat had a bit more bass response which I tend to favor. Does anyone know what caps I should modify to get a bit more bass response out of a ce-2? I have attached a schem. Thanks!

Greetings

Re: Boss ODB-3 intermittent sound.

I have recently found in my collection of pedals, one of them.

The problem is that when I step on the pedal to turn it on, the sound is faded. It sounds like the effect is only kicking in very little. If I keep my foot down on the pedal, the sound Is perfect. I believe something is wrong in the switching circuit. I've tried looking for a schematic but haven't had any luck. Any insight would be helpful.
I'm using a Voodoo Labs ISO 5 power supply...

I'm looking for for a solution to popping that's occurring with a 4PDT and SPDT in a circuit by potentially utilizing a microcontroller. I've read that they can be programmed to briefly mute the signal as they switch, which can eliminate popping. It's something I'd eventually love to learn how to program and implement myself but in the mean time, does anybody know of anyone with this knowledge/experience that could provide this service?

Hey all, I've been lurking around here for a while but thought I'd post with a question.

After attempting to install some new op-amps from the fromel mod kit for the Boss Ge-7, it's not working in a ... weird way. No bypass, no clean, just a loud buzz like something's connected to ground. The weird thing is whenever i depress the toggle all the way, the bypass signal comes through just fine. This isn't my first mod or even build, but I haven't really messed with buffered bypass before: does...

I want to make a tails switch for a DBD. There are multiple examples on the internet, but I just can not seem to get it to work correctly. Must be my lacking knowledge of transistors, so I am here to be taught :D

Attached a picture by R.G. Keen with a basic jFet switch as in boss/ibanez. If I am not mistaken when Vgs > V cuttoff the switch will be closed and if Vgs Closed
V control = ground (0V), Vref 4,5V makes Vgs 0-4,5 = -4,5V which is in the Vcuttoff range -> Open

However... which ever...

Hello all.

I'd really appreciate some help with my build please, if possible. I have followed the troubleshooting steps in the FAQs but nothing seems to have had any effect. This is my first build with a PCB rather than a veroboard which I though would be more straightforward. That was certainly the kiss of death!

The kit is the Supreme Compressor from Effect Pedal Kits. It is based on the Valvewizard Engineer's Thumb, with 4 control knobs.

A lot of fuzz-like distortion is being produced...

Got it from someone that said they used the wrong power supply. What is the label on D6? Is it 5A9D?

6E75F7BF-6761-4771-AB0E-DF85838F9AC6.jpeg

Hello,

This is my first pedal build and seemed to have hit a snag and not sure how to follow through or what to change from what I have. I'm following an old PDF from GEO Fex
I'm trying to do this Terminal Strip method and have gotten as far as the tuning process, inserting 100k and 10k pot to get a proper voltage reading from the collector and ground to set the transistor gain properly.

The PDF states a -6.8 to -7.2 voltage from the collector and ground is what is usually desired to get...

This is a weird thing I noticed, the Meatsmoke preamp has a buffer at the end of the circuit and a switch that allows attenuation of the output signal

Verellen Meatsmoke.png

While various Kingsley pedals for example doesnt seem to have one

Kingsley Harlot schemtic.jpg

On the Kingsley I dont see much of signal attenuation compared to the Meatsmoke, considering this is a high voltage tube pedal doesnt this make the output of the Kingsley too hot for most pedals after it?

HI, I seem to have lost my login as it's been a few years, so I am new and shiny

I was searching the threads and found some info on how to make the reissue of the Ibanez WH10 sound more like the original (cap removal) and about true bypassing, BUT i can't find anywhere any good information on how to add a volume control to reign in the gain boost you get on these pedals. I know people do it but for some reason to my knowledge no one has ever posted how best to do it. So if anyone could advise...

Hi all, I have an issue with the line6 m13. All effects work but the lcds are either blank or black boxes. (LCD colour backgrounds still work) It seems a pretty common issue when looking online, but there doesn’t seem to be any solutions.
Has anyone had experience with this or any thoughts on what to try. Service manual is available online.
Thanks

Hi all, my line6 m13 has blank lcd screens. The colours still change and the effects all still work. But unfortunately the lcds are either blank or sometimes all black. Looking online it seems like a few people has this issue but I haven’t found a way to repair it yet.
Does anyone have any advice? Thanks

I was making a Guitarpcb Pump'd up Tonebender, v4. I am able to get fuzz, but it is sputtery and at a lower volume. Below are my voltages for the IC and transistors. I am worried that I blew two transistors (Q1 and 2). My father, who is a EE, walked me through the process to test the transistors with a volt meter, comparing the resistance of the B to each C and E. I am confused how the pedal can potentially have two blown transistors and still work, creating fuzz (yet bad fuzz). Do these...

Hello,

I need help with my CE-2 build. I bought the Cepheid Chorus board from Pedal PCB, so I am relatively sure that the problem is not a board problem. I am getting a signal coming through when I plug the pedal in, but there is no chorus sound. This is probably because of the R34 47K leak resistor seen at the very top of the schematic. There is no chorus sound, however. I have probed with an oscilloscope, so I know that there is a signal going into the MN3207 chip I am using, as well as...

I bought some 12v 1W diodes. I've repaired these in the past where this was the issue and is in the repair notes linked below as a common symptom of the no power issue.

I replace the diode and I get no power and the PCB at D-6 gets extremely hot. I had to remove part of the trace as it came up.

Anyone have any other thoughts on how to troubleshoot this? Below is the schematic and link to a BossArea thread: