Hey everyone!

I built the Electric Lover project from Guitar PCB Mania. Its a modernized Electric Mistress clone. It is passing signal, but I cannot get it to bias up correctly. There is only a small range of the BIAS trimpot near max-clockwise position that allows signal to pass, regardless of the settings for the CLOCK, T1 (max feedback), and VOLUME trimpots. Here are the directions for the setup:

Set Clock and Bias in the middle, at 12 o’clock.
Set T1 and the Rate knob fully...

Is it possible to run the cloned centaur on 12V or 18V ?

When opening up the case of my MXR carbon copy the stomp switch fell apart. I replaced it but now the pedal does not pass signal. Well, actually you still can hear the pop being delayed when either the battery or input is plugged in with the pedal turned ON. There is no signal with switch in both positions otherwise.

I have soldering experience working on tube amps but little on pedals and PCB's. I wonder if I damaged the board or something? The original switch was a major pain to get out and...

Hello everyone! I recently purchased the Sun Beta Lead kit through Das Musikding. I've just finished assembling the pedal and I've noticed that I wired the DC Jack reverse. So I corrected the issue and the LED turns on but the pedal emits a continuous, very high pitched whistle and if tapped on the enclosure it makes a very loud pop through my amp. I don't know if some component failed or something else...I don't know what to do!

Hi all,

I recently purchased a Sunn beta lead kit (schematic pcb guitar mania here After soldering everything, I just have a huge hissing sound, sometimes with kind of distortion, but nothing else, the sound is pretty unstable and reacts really bad to any note I can play.

The circuit is built around a charge pump that is supposed to deliver -15/+15 from a LT1054, and this component is really overheating as soon as I plug the pedal.

I checked the current delivered after the charge pump and...

Hello! Longtime lurker, first time poster.

I recently built this pedal. All seems well but when I turn it on, I get a rhythmic clicking and the LED pulses at the same right. No signal is passed (though it passes freely when in bypass) and adjusting the rate knob does not alter the rate of the click/led. This seems like a very specific issue so I'm hoping there's *a* cause that somebody can direct me to?

Hello,

I'm not skilled in electronics but there's maybe something wrong in this circuit or in my building...
When I use 6 stages phaser it's ok and I like the sound but when I switch to 5 stages phaser then there's evidently a lack of bass, as if there was an high pass filter somewhere... In the forum, someone else says the same thing about this circuit.

Does anyone have the pdf file of the tracks layout for this PCB?
I would like to cut the track that goes from R24 to R26 in order to switch...

I built the Master Phaser from PCB Guitar Mania and the functionality seems to be all there. However, the switch (which I believe switches between 5 and 6 stages) also causes a pretty big bass cut - like a high pass filter - when switched to the DOWN position. I don't know what number of stages is UP switch and DOWN switch as this is not in the documentation. Surely this isn't normal?

I know it might be a more obscure build and maybe I am unsure of the nature of 5 and 6 stage phasing and...

Hello everyone,

happy to make my first post, sad because it starts with a problem.

I built an Orange Rockerverb Preamp based on the attached schematic from pcb mania. It's a relativly straight forward build using the Rockerverb preamp circuit and replacing the tubes with j201 jfets. I dialed the jfets to 4.5V and everything sounds fine.
However as soon as I play hard on the guitar the sound slowly starts distorting and finally cuts out completely.
I measured the voltage on Q1 and I can see...

Hi folks,

I recently put together my first ever build, the PCB Guitar Mania Black Mirror which is a B3K clone. Schematics and layout can be found here:
This circuit also has a section to insert an EQ circuit. I wired up the Falcon EQ circuit, schematics and layout are here:

Initially, I was getting a signal through the pedal although none of the pots seemed to do anything, and now I am not getting any signal through at all. I traced the DC voltages which can be seen here:

I also put...