[MOD] Ibanez AD9 with doubled delaytime
- Dirk_Hendrik
- Old Solderhand
Information
As well as thanks to the CoolAudio V3205 re-release on the MN3205:
schem:
http://www.dirk-hendrik.com/ibanez_ad9_memextension.pdf
schem:
http://www.dirk-hendrik.com/ibanez_ad9_memextension.pdf
- bajaman
- Old Solderhand
Information
- Posts: 4549
- Joined: 26 Jun 2007, 21:18
- Location: New Brighton, Christchurch, NZ
- Has thanked: 596 times
- Been thanked: 2061 times
Thanks Dirk
bajaman
bajaman
- briggs
- Tube Twister
Information
- Dan N
- Resistor Ronker
Nice! Kind of like the way Scott Swartz did it but keeping the Ibanez values.
What I wonder is how to get pornographic and use another clock and pair of chips. Dual gange delay pot?
So, how does it sound? The V3205's I tried had much more output than the MN3205.
What I wonder is how to get pornographic and use another clock and pair of chips. Dual gange delay pot?
So, how does it sound? The V3205's I tried had much more output than the MN3205.
- Dirk_Hendrik
- Old Solderhand
Information
@ Dan,
The output levels of the coolaudio chip aren't of much concern. The filtering electronics before and after the BBD's still have a far larger headroom than the BBD's itself.
@Serge,
If you take a look at the schematic you will notice that the 8 testpoints used correspond to the pins of a MN3205. Under one of the 2 chips these testpoints are arranged in such a way that with 8 pieces of wire at the bottom side of the piggyback board they stick into the main PCB in a 1 to 1 connection.
The output levels of the coolaudio chip aren't of much concern. The filtering electronics before and after the BBD's still have a far larger headroom than the BBD's itself.
@Serge,
If you take a look at the schematic you will notice that the 8 testpoints used correspond to the pins of a MN3205. Under one of the 2 chips these testpoints are arranged in such a way that with 8 pieces of wire at the bottom side of the piggyback board they stick into the main PCB in a 1 to 1 connection.
Information
- Posts: 1
- Joined: 16 May 2009, 08:44
- my favorite amplifier: Marshall 100w plexi
- Completed builds: stationary wah
How do I get a daughter board like that? I want one!Dirk_Hendrik wrote:As well as thanks to the CoolAudio V3205 re-release on the MN3205:
schem:
http://www.dirk-hendrik.com/ibanez_ad9_memextension.pdf
- Dirk_Hendrik
- Old Solderhand
Information
- danielzink
- Resistor Ronker
Information
- Posts: 389
- Joined: 23 Feb 2008, 19:27
- Completed builds: Too many: www.danielzink.com
- Location: Lansing, MI
- Has thanked: 8 times
- Been thanked: 27 times
noiseuoh wrote:Just curious if any1 could explain where i connect the daughter board to? i couldnt make it out from the schematic. is there another 8pin chip underneath the daughter board?
The daughter board is going to plug into the orginal spot where the single BBD used to be.
Use this as a reference:
http://www.danielzink.com
MoonWatcher wrote: Silent ain't better. If someone cracks the shitwind, I want to know what's headed my way. Silence is for the library and the cemetery.
- puppiesonacid
- Cap Cooler
Can this be done with the reissue ad9? Jist licked one up and the seller "didn't notice" there some issues with what he was selling And now he's gone silent. Stupid me...since ime going to be fixing the issues...getting curious.