The complete BBD clock archive

Stompboxes circuits published in magazines, books or on DIY electronics websites.
Post Reply
User avatar
Fender3D
Cap Cooler
Posts: 531
Joined: 08 Aug 2009, 03:40
Location: Helltaly
Has thanked: 104 times
Been thanked: 136 times

Post by Fender3D »

Hello guys,

I hope this is the proper board for this thread

I noticed this great forum lacks the main info about BBD based pedals...
CLOCK.

Heck, we can search for every fuzz face's single node voltage, we have constant requests about "what voltage here and/or there" in workbench board...
but we have few or no info about BBD based pedals clocks.

I think we need an exaustive clocks archive if we wanna properly clone BBD based pedals.

I think max. and min. clock measured @ BBD pins and power supply used should be enough to nail THAT sound or, at least, to estimate delay time.

Please add your suggestions and/or tips.

Thanks.

This might be an example:

MXR Micro flanger:
I powered it with a stabilized power supply @ 9.6V
max clock freq at SAD's pin 1 is 850KHz (@ min rate)
min clock freq at SAD's pin 1 is 133KHz (@ min rate)

Scruffie
Tube Twister
Posts: 1754
Joined: 13 Mar 2009, 18:59
my favorite amplifier

Whatever sounds best at the time

Location: London.. ish, Uk
Has thanked: 25 times
Been thanked: 132 times

Post by Scruffie »

EHX Echoflanger Frequencies courtesy of Graemey's Stompbox Secrets, taken at Pin1 of the 4013.

Tune - CW
Width - CCW
Rate - CCW
Feedback - CCW
Filter Matrix 341kHz
Double Track 110.9khZ

Tune - CCW
Width - CCW
Rate - CCW
Feedback - CCW
Filter Matix 54.5kHz
Double Track 17.71kHz

Tune - CW
Width - CW
Rate - CCW
Feedback - CCW
Flange 439-50kHz
Chorus 114-82kHz

Scruffie
Tube Twister
Posts: 1754
Joined: 13 Mar 2009, 18:59
my favorite amplifier

Whatever sounds best at the time

Location: London.. ish, Uk
Has thanked: 25 times
Been thanked: 132 times

Post by Scruffie »

I collected some readings from another 2 Echoflanger after helping people debug them and set the clock to the factory setting.

1st Unit.

Settings
Tune - CW
Width - CCW
Rate - CCW
Feedback - CCW

Filter Matrix - 250kHz
Double Track - 66kHZ

Settings
Tune - CCW
Width - CCW
Rate - CCW
Feedback - CCW

Filter Matrix - 36kHz
Double Track - 10kHz

Settings
Tune - CW
Width - CW
Rate - CCW
Feedback - CCW

Flanger 35 - 330kHz
Chorus 14 - 20khZ

Second Unit

Settings
Tune - CW
Width - CCW
Rate - CCW
Feedback - CCW

Filter Matrix - 261kHz
Double Track - 81kHZ

Settings
Tune - CCW
Width - CCW
Rate - CCW
Feedback - CCW

Filter Matrix - 43kHz
Double Track - 14kHz

Settings
Tune - CW
Width - CW
Rate - CCW
Feedback - CCW

Flanger 40 - 365kHz
Chorus 20 - 28khZ

User avatar
Dirk_Hendrik
Old Solderhand
Posts: 4249
Joined: 03 Jul 2007, 09:44
Location: Old Amsterdam
Has thanked: 221 times
Been thanked: 832 times
Contact:

Post by Dirk_Hendrik »

How easy it would be to add the P/N of the chip to the summing up. :secret:
Sorry. Plain out of planes.

http://www.dirk-hendrik.com

Scruffie
Tube Twister
Posts: 1754
Joined: 13 Mar 2009, 18:59
my favorite amplifier

Whatever sounds best at the time

Location: London.. ish, Uk
Has thanked: 25 times
Been thanked: 132 times

Post by Scruffie »

Dirk_Hendrik wrote:How easy it would be to add the P/N of the chip to the summing up. :secret:
Scruffie wrote:EHX Echoflanger Frequencies courtesy of Graemey's Stompbox Secrets, taken at Pin1 of the 4013.

tube-exorcist
Cap Cooler
Posts: 465
Joined: 05 Jul 2007, 21:09
Has thanked: 168 times
Been thanked: 61 times

Post by tube-exorcist »

Isn´t normally meant with "P/N" the Part Number (e.g. SAD1024; MN3007) instead of the pin number of the clock driver ?

Just asking....
"I've noticed there's an inverse relationship between cost of gear and talent. If you need the most expensive gear to get decent tones, then you suck as a player."

User avatar
Fender3D
Cap Cooler
Posts: 531
Joined: 08 Aug 2009, 03:40
Location: Helltaly
Has thanked: 104 times
Been thanked: 136 times

Post by Fender3D »

MXR Flanger M117 courtesy of Dave oldschoolanalog @diystompboxes

readings taken at BBD's pins

stock power supply 15V

Unit1:
Width fully CCW
Manual fully CW 29KHz
Manual fully CCW 960KHz

Unit2:
Width fully CCW
Manual fully CW 32KHz
Manual fully CCW 965KHz

User avatar
Fender3D
Cap Cooler
Posts: 531
Joined: 08 Aug 2009, 03:40
Location: Helltaly
Has thanked: 104 times
Been thanked: 136 times

Post by Fender3D »

ROSS Flanger w/SAD1024 courtesy of miketbass @ DIYstompboxes

readings @ SAD's pin 8:

stock power supply 15V

manual full CCW: 32KHz
manual full CW: 625KHz

User avatar
Fender3D
Cap Cooler
Posts: 531
Joined: 08 Aug 2009, 03:40
Location: Helltaly
Has thanked: 104 times
Been thanked: 136 times

Post by Fender3D »

DOD Chorus FX65B

Min clock 62.5KHz
Max clock 71KHz

Courtesy of hemisfeer

Sendy CZ
Posts: 3
Joined: 08 Dec 2013, 03:22
Been thanked: 1 time

Post by Sendy CZ »

Ibanez UE400 - first version (1980?) with distortion (not overdrive) and compressor section with CA3080 OTA :
Flanger/Stereo Chorus section with NE571, MN3007, MN3101 :
min. clock 40-45kHz (WIDTH = CCW, SPEED = CCW, FEEDBACK = CCW)
Chorus and Flanger clock is the same

Post Reply