Lovetone - Brown Source  [traced]

General documentation, gut shot, schematic links, ongoing circuit tracing, deep thoughts ... all about boutique stompboxes.
User avatar
DougH
Transistor Tuner
Information
Posts: 1087
Joined: 18 Aug 2007, 04:53
Has thanked: 4 times
Been thanked: 23 times

Post by DougH »

BTW, I think this is a really nice demo of what the Brown Source can do:
"You have just tubescreamered or fuzzfaced yourself " -polarbearfx

User avatar
ryanuk
Solder Soldier
Information
Posts: 211
Joined: 29 May 2008, 11:18
Has thanked: 29 times
Been thanked: 28 times

Post by ryanuk »

DougH wrote:BTW, I think this is a really nice demo of what the Brown Source can do:
The demo of the BS vs the Tube Screamer is cool. The BS deffo is lower gain and a little different sounding to the TS.

The rest of clip is alittle dissappointing. The Drive and Vol are left up FULL for the majority of the time and makes the BS effect indestinguishable. It could easily have been a SD1, DS1, katana, micro amp, DOD250, TS, gainster yada yada...

I would have been more interested in hearing more of the natural BS.

User avatar
DougH
Transistor Tuner
Information
Posts: 1087
Joined: 18 Aug 2007, 04:53
Has thanked: 4 times
Been thanked: 23 times

Post by DougH »

I think the demo did a good job of showing the effect of the rotary switch. FWIW I rarely use the drive control on less than max. There's a good review of it on HC that describes how it does "something" but he's not sure exactly how to describe it. I think it is as much an EQ as it is an overdrive.
"You have just tubescreamered or fuzzfaced yourself " -polarbearfx

User avatar
modman
a d m i n
Information
Posts: 4890
Joined: 19 Jun 2007, 16:57
Has thanked: 4394 times
Been thanked: 2131 times

Post by modman »

Attachments
Lovetone Brown Source corrected schematic
Lovetone Brown Source corrected schematic
705861406_o.jpg
705861440_o.jpg
Lovetone - Brown Source
Lovetone - Brown Source
Lovetone - Brown Source
Lovetone - Brown Source
Lovetone - Brown Source
Lovetone - Brown Source
Please, support freestompboxes.org on Patreon for just 1 pcb per year! Or donate directly through PayPal

User avatar
lionhead
Information
Posts: 2
Joined: 16 Apr 2010, 19:13

Post by lionhead »

Anyone successfully built a Brown Source with Lacesensor's vero layout?

On mine everything works as it should except the output volume is very low and when the volume pot is turned there is some noise. It sounds as if there is DC on the pot. I replaced the pot and had the same results.

Has anyone here experienced this?

User avatar
alex28m
Information
Posts: 5
Joined: 13 Feb 2016, 21:30
my favorite amplifier: JTM45
Completed builds: various commercial
Location: Pacific
Has thanked: 4 times
Been thanked: 4 times

Post by alex28m »

Could someone please post some high-resolution photos of the component side of the Brown Source PCB? Showing the capacitors and resistor positions? :?:

Also, there seems to be conflicting information on the web around what the correct capacitor values should be. :?
Modman: Your schematic shows 220nF capacitors in several places, another two schematics I found show 22nF in identical positions ? :?: :?:

Any chance someone could put up a list of the capacitors with their position designators and the value on the capacitor e.g. C1: 223K or 224K or 224J or whatever is in the original Lovetone Brown Source PCB positions? :?: Please....

Check out the attached schematics...to see what I'm getting and why I'm :? :?

I'm trying to reassemble a friends Brown Source after some DIY modifications went wrong and they pulled out ever part and never kept a list of what went where; so now I have a guessing game of what goes where. Also he's lost some of the capacitors :roll: :roll:
Tried contacting the Lovetone people in the UK; but their standard response is silence.

Thanks,

Alex. :block:
Attachments
Lovetone Brown Source (V5) (C).pdf
(128.07 KiB) Downloaded 311 times

User avatar
LaceSensor
Cap Cooler
Information
Posts: 585
Joined: 02 Jan 2011, 12:01
Has thanked: 57 times
Been thanked: 277 times

Post by LaceSensor »

In the interest of posterity, I can provide what is asked for here as I had a recent request, and took the liberty to scan / redraw the parts layout and traces of my real Brown Source

Sorry its 3 years late (!)

There are a lot of versions of this floating on the internet. This is traced from my own v4T from 1996 (quite an early one, S/N 0094). My actual unit as its early has a cap tacked on, and a trace missing that was addressed with kynar wire. I have modified the traces to take account for this, should someone with to actually produce an etch of this layout.

Image


Image

User avatar
LaceSensor
Cap Cooler
Information
Posts: 585
Joined: 02 Jan 2011, 12:01
Has thanked: 57 times
Been thanked: 277 times

Post by LaceSensor »

Just a heads up the 22nF caps should be 220nF caps. Sorry! Easy fix...

verified

Image

Image

User avatar
LaceSensor
Cap Cooler
Information
Posts: 585
Joined: 02 Jan 2011, 12:01
Has thanked: 57 times
Been thanked: 277 times

Post by LaceSensor »

adjusted trace parts overlay provided.

also added PDF with scaled (print at 100%) for the transfer
Brown to print.pdf
(258.83 KiB) Downloaded 185 times
parts with further annotation FIN.jpg

User avatar
LaceSensor
Cap Cooler
Information
Posts: 585
Joined: 02 Jan 2011, 12:01
Has thanked: 57 times
Been thanked: 277 times

Post by LaceSensor »

The previously posted etchable PDF is correct
However there was a slight trace position issue on the parts layout (so anyone using this to make a vero might have made a booby...)
Its the 33nF cap off the tone control.

heres the fixed copy. Enjoy

This is built and verified by the way .
parts with further annotation FIN.jpg
1.jpg
4.jpg

Post Reply