WTT Parts & PCBs for PCBs From DIYLC pnps & Parts

Looking for a particular component or hardware part and you just cannot find it? Got comoonents surplus and want to get rid of it? Post it all here... No sales of working pedals, put these in the 'Seen for sale' section please.
Post Reply
User avatar
Scruffie
Opamp Operator
Information
Posts: 1740
Joined: 13 Mar 2009, 17:59
Location: UK
Has thanked: 28 times
Been thanked: 169 times

Post by Scruffie »

Right... i'm after a few PCBs etched up from DIY Layout Creator Layouts and some parts in Exchange for any of this stuff -

1 x Dallas Rangemaster PCB
1 x NOS Full Legged Metal Can NKTOC44
1 x TonePad Tone Bender MkII PCB
1 x OPA2134PA Dual Op-Amp - New
1 x MAX1044 - New
1 x MAX1771 - New
1 x HPro PS200R Power Supply - Good as New
2 x Vintage RCA741 Op-Amps - Desoldered
5 x NPN BCE Pin Out 70s Silicon Transistors - Snipped (Have a few sets)
5 x PNP BCE Pin Out 70s Silicon Transistors - Snipped (Have a few sets)
5 x 70s/80s D-Shaft Pot Knobs (I'll add pictures later, Black with silver fronts)
1 x Reverb Tank
1 x Black Pearloid Strat Scratch Plate (Slightly enlarged pickup holes, will still take normal pickups fine though)
1 x Fender Amp Name Plate
1 x Set of Strat Trem Springs & Claw
Various BB and TI Op-Amps.

I'm after any of these parts - (Don't care about brands for any of it)
-----------------------------------------------------------------------------
1 x Hammond 125A Transformer
1 x 12AU7 or ECC99
3 x Vactrols or LED/LDR Combos
1 x 12AX7
1 x 13600 or 13700 Chip
1 x 4009 Chip
2 x 4013 Chips
3 x 3102 Clock Drivers
1 x 3207 Chip
Various Valued Right Angled Board Mount Pots Like SmallBear Sell
Trim Pot Knobs (Like Solderman Used Here - http://solderman.fatabur.se/f/u3.jpg )

And These Layouts - (Hope this is okay with the original creators, say if not)
-----------------------------------------------------------------------------------------
Octave Mulitplexer - http://www.aronnelson.com/gallery/main. ... 1.gif.html
Super Fly - https://i210.photobucket.com/albums/bb2 ... flyPnP.gif
Rebote 2.5 - http://cfs3.tistory.com/upload_control/ ... AvMjAuZ2lm
Dr Boogey - https://i210.photobucket.com/albums/bb2 ... giePnP.gif
Another Dr Boogey - http://www.aronnelson.com/DIYFiles/up/D ... ansfer.pdf
Top
User avatar
azrael
Cap Cooler
Information
Posts: 565
Joined: 02 Jun 2009, 14:07
Has thanked: 35 times
Been thanked: 87 times

Post by azrael »

I believe that trimpot that solderman used is a normal one, he just glued on a knobbie thing.
Top
User avatar
Scruffie
Opamp Operator
Information
Posts: 1740
Joined: 13 Mar 2009, 17:59
Location: UK
Has thanked: 28 times
Been thanked: 169 times

Post by Scruffie »

azrael wrote:I believe that trimpot that solderman used is a normal one, he just glued on a knobbie thing.
Yeah The trimpot bit is normal, but I want the knobs that fit them, they have little sorta phillips head inserts.
Top
Post Reply

Return to “Parts & Tools Sourcing & Trading”