FS - Electronics House Clearance
Posted: 30 Aug 2012, 08:31
Clearing out as much of my stock as I can to get awaiting projects finished to move away from the hobby!
PCBs...
1 x PNP Fuzz Face PCB W/ Input Trim, Bias Pot & MAX1044 to use standard negative ground!
$5/£2 (Unverified Layout but checks fine)
All of them will fit a 1590B + Battery with a little planning and are from my own layouts all using Onboard pots (Mount on back of PCB) no stand up resistors and are well etched, drilled and cut to size. (Layouts Linked at Bottom)
1 x LT1054 Charge pump board
$3/£1
ICs & Transistors
4 x Vintage 70s House Branded LM324s, Cool for Electric mistress builds? Look like this 741 Chip $1/£0.50 each http://en.audiofanzine.com/utilities/a. ... ctures.jpg
5 x House stamped 2N2925 transistor pulls (tested & with decent lead length) for Vox Wahs $3/£1.50 the set (more available on request).
2 x Vintage RCA CA3080E OTAs (package like the 741 pictured above) $5.50/£3 each
1 x Vintage RCA 3080 (House Branded) $3/£1
1 x Harris CA3080 $4/£2
2 x Vintage RCA 741s (as above) for DOD 250s $4.50/£2 each
1 x AD781 Sample & Hold chip, very rare chip, used in the BugBrand Bug Crusher Bit Crusher DIY Project
£5/$10
http://www.bugbrand.co.uk/bugbrand_old/ ... ronics.htm
Very simple design if you want a Bit Crusher effect!
1 x MN3206 BBD, 128 Stages, Pulled but tested, would be good for a through zero flanger. £4/$7
1 x MN3102 Clock, Pulled & Untested (assume it works though) will pair with 3206 for an extra $1.50/£1
3 x TCA350Y BBDs, 185 Stage BBDs, think these were the first BBDs ever produced, used in old Organ choruses, very rare £5/$10.
1 x Mullard OC44 Ge Transistor, Pulled from an 60's radio but with useable lead length £3/$5
1 x Mullard OC45 Ge Transistor, Pulled from an 60's radio but with useable lead length £2/$5
Tubes (May be able to offer more on request)
1 x NOS Raytheon 6088 Output Pentode, could be used to build a miniature amp or even a battery powered booster due to its very low current draw (10.5mW output power, 20mA/1.25V filament current/voltage, 67.5V Max Plate) $8/£4 - Tested for functionality.
2 x 5840 Pentode Tube (RCA & CV Brand) Legs have been cut down but there's enough to fit a DIP-8 socket, both tested. $7/£3.50
Used in a few Frequency Central designs.
Not sure about this one... just don't know when i'll find time to finish it.
EHX Super Space Drum 3 PCB Set to Build Either the Standard 3 knob Space drum or use the 2 add on PCBs for LFO and/or Sweep & Decay Controls to build a Super Space Drum.
Converted for LM13600 from CA3094, really nice PCBs using onboard pots.
$25/£15 the Set or make me an offer.
More Stuff to Come!
Will trade for drilling and finishing of enclosures, something I no longer have the time or means to do.
Also, depending on the price, location and weight of your order it will be shipped free either first class or airmail but that will be done on my discretion. I'll also do discount bundle orders and happily haggle, the prices are set at either guesses or below cost of similar ebay items. Try low balls, I may accept them.
Depending on request I can also assist with extra parts you may need for builds with orders for free or smaller charge than cost... Even rarer parts.
PCBs...
1 x PNP Fuzz Face PCB W/ Input Trim, Bias Pot & MAX1044 to use standard negative ground!
$5/£2 (Unverified Layout but checks fine)
All of them will fit a 1590B + Battery with a little planning and are from my own layouts all using Onboard pots (Mount on back of PCB) no stand up resistors and are well etched, drilled and cut to size. (Layouts Linked at Bottom)
1 x LT1054 Charge pump board
$3/£1
ICs & Transistors
4 x Vintage 70s House Branded LM324s, Cool for Electric mistress builds? Look like this 741 Chip $1/£0.50 each http://en.audiofanzine.com/utilities/a. ... ctures.jpg
5 x House stamped 2N2925 transistor pulls (tested & with decent lead length) for Vox Wahs $3/£1.50 the set (more available on request).
2 x Vintage RCA CA3080E OTAs (package like the 741 pictured above) $5.50/£3 each
1 x Vintage RCA 3080 (House Branded) $3/£1
1 x Harris CA3080 $4/£2
2 x Vintage RCA 741s (as above) for DOD 250s $4.50/£2 each
1 x AD781 Sample & Hold chip, very rare chip, used in the BugBrand Bug Crusher Bit Crusher DIY Project
£5/$10
http://www.bugbrand.co.uk/bugbrand_old/ ... ronics.htm
Very simple design if you want a Bit Crusher effect!
1 x MN3206 BBD, 128 Stages, Pulled but tested, would be good for a through zero flanger. £4/$7
1 x MN3102 Clock, Pulled & Untested (assume it works though) will pair with 3206 for an extra $1.50/£1
3 x TCA350Y BBDs, 185 Stage BBDs, think these were the first BBDs ever produced, used in old Organ choruses, very rare £5/$10.
1 x Mullard OC44 Ge Transistor, Pulled from an 60's radio but with useable lead length £3/$5
1 x Mullard OC45 Ge Transistor, Pulled from an 60's radio but with useable lead length £2/$5
Tubes (May be able to offer more on request)
1 x NOS Raytheon 6088 Output Pentode, could be used to build a miniature amp or even a battery powered booster due to its very low current draw (10.5mW output power, 20mA/1.25V filament current/voltage, 67.5V Max Plate) $8/£4 - Tested for functionality.
2 x 5840 Pentode Tube (RCA & CV Brand) Legs have been cut down but there's enough to fit a DIP-8 socket, both tested. $7/£3.50
Used in a few Frequency Central designs.
Not sure about this one... just don't know when i'll find time to finish it.
EHX Super Space Drum 3 PCB Set to Build Either the Standard 3 knob Space drum or use the 2 add on PCBs for LFO and/or Sweep & Decay Controls to build a Super Space Drum.
Converted for LM13600 from CA3094, really nice PCBs using onboard pots.
$25/£15 the Set or make me an offer.
More Stuff to Come!
Will trade for drilling and finishing of enclosures, something I no longer have the time or means to do.
Also, depending on the price, location and weight of your order it will be shipped free either first class or airmail but that will be done on my discretion. I'll also do discount bundle orders and happily haggle, the prices are set at either guesses or below cost of similar ebay items. Try low balls, I may accept them.
Depending on request I can also assist with extra parts you may need for builds with orders for free or smaller charge than cost... Even rarer parts.