A Switching Scheme  [documentation]

Original effects with schematics, layouts and instructions, freely contributed by members or found in publications. Cannot be used for commercial purposes without the consent of the owners of the copyright.
User avatar
moosapotamus
Information
Posts: 17
Joined: 14 Sep 2007, 01:31
Location: New Hampshire USA
Been thanked: 5 times
Contact:

Post by moosapotamus »

I made PCB/perf layouts for both versions...

Latching SPDT Footswitch
Image
Image

Momentary SPDT Footswitch
Image
Image

I tried to make them as small and compact as possible while still having a single-sided layout for easy DIY etching. The component numbering follows the schematic that mmolteratx posted here...
viewtopic.php?f=13&t=13295&start=120#p215994

Here it is, for those that do not have Eagle...
Image

Footprint for the relay in both layouts is setup to ground the circuit input (SND) when bypassed. The momentary switch version is verified by me. The latching switch version should be good too, since it was just copied/pasted.

Thanks, mictester!

~ Charlie
moosapotamus.net
"I tend to like anything that I think sounds good."

User avatar
Duckman
Opamp Operator
Information
Posts: 1492
Joined: 20 May 2009, 01:45
Has thanked: 320 times
Been thanked: 134 times

Post by Duckman »

Thanks, looks great and neat.
How about those 40106 unused pins? :hmmm:

User avatar
Cub
Cap Cooler
Information
Posts: 458
Joined: 29 Aug 2011, 07:14
Location: The Netherlands
Has thanked: 102 times
Been thanked: 118 times

Post by Cub »

Splendid ! Thank you. :applause:
If somebody will be etching and drilling a batch of the latching boards, I'd be very happy to buy a bunch.
I wish I were a chestnut tree, nourished by the sun.
With twigs and leaves and branches and conkers by the ton.

User avatar
gian80
Information
Posts: 4
Joined: 06 Dec 2009, 09:36
Has thanked: 1 time

Post by gian80 »

Hi,

I can't find the Takamisawa relay and considering it's xmas time I should wait a lot ordering them from Taywan.


I found Banzai effect having Panasonic TQ2-L-5 relay, they cost the double I know, but I need one and usually it takes 7 days to get the package. I checked and it's a singol coil bistable latching relay, if I'm not wrong it's exactly Mictester Specs.


Thank u all

User avatar
abakuzam
Information
Posts: 48
Joined: 16 Jul 2010, 12:48
Has thanked: 11 times
Been thanked: 22 times

Post by abakuzam »

hi, can we make relay true bypass with bistable 2coil latching relays? with momentary seitch of course, i think all i have to do is cut the power on and off with momentary?
i found a schematic : http://www.electroschematics.com/6546/l ... ent-relay/ and the relay im thinking to use is : Nais TQ2-L2-5V http://pdf1.alldatasheet.com/datasheet- ... -L-5V.html

Thanks.

User avatar
electrosonic
Breadboard Brother
Information
Posts: 130
Joined: 28 Nov 2008, 16:53
Location: Vancouver, BC
Has thanked: 27 times
Been thanked: 19 times

Post by electrosonic »

The schematic you link to is almost identical to mictester's schematic and requires a single coil bistable relay and a SPST switch (not momentary).

There are variations using a momentary switch earlier on in this thread.

Andrew.

User avatar
abakuzam
Information
Posts: 48
Joined: 16 Jul 2010, 12:48
Has thanked: 11 times
Been thanked: 22 times

Post by abakuzam »

electrosonic wrote:The schematic you link to is almost identical to mictester's schematic and requires a single coil bistable relay and a SPST switch (not momentary).

There are variations using a momentary switch earlier on in this thread.

Andrew.
i looked at them, but i dont want to use nothing but momentary switch and relay? is that posible? and i found this: http://www.paulinthelab.com/2013/04/sof ... h-for.html

Thanks, sorry for my noob questions and my english.

User avatar
electrosonic
Breadboard Brother
Information
Posts: 130
Joined: 28 Nov 2008, 16:53
Location: Vancouver, BC
Has thanked: 27 times
Been thanked: 19 times

Post by electrosonic »

Have you read the whole thread? This is from the 3rd or 4th page...

https://www.freestompboxes.org/download/ ... &mode=view

Andrew.

User avatar
abakuzam
Information
Posts: 48
Joined: 16 Jul 2010, 12:48
Has thanked: 11 times
Been thanked: 22 times

Post by abakuzam »

electrosonic wrote:Have you read the whole thread? This is from the 3rd or 4th page...

https://www.freestompboxes.org/download/ ... &mode=view

Andrew.
i saw that of course i read whole thread, but i dont want to use 4016 etc. i just want to know this type of bypass can be make with momentary switch and the relay only, not other chips like 4016,555,programmables etc.

Kemal.

User avatar
electrosonic
Breadboard Brother
Information
Posts: 130
Joined: 28 Nov 2008, 16:53
Location: Vancouver, BC
Has thanked: 27 times
Been thanked: 19 times

Post by electrosonic »

I guess the short answer is no. (But I would be like to be proved wrong)

The simplest scheme for a latching relay I have come across is something like this -

Image

(Not my image btw)

This is using a SPDT (non momentary) switch.

Andrew.

User avatar
abakuzam
Information
Posts: 48
Joined: 16 Jul 2010, 12:48
Has thanked: 11 times
Been thanked: 22 times

Post by abakuzam »

electrosonic wrote:I guess the short answer is no. (But I would be like to be proved wrong)

The simplest scheme for a latching relay I have come across is something like this -

[ Image ]

(Not my image btw)

This is using a SPDT (non momentary) switch.

Andrew.

Thanks.

User avatar
Pruttelherrie
Solder Soldier
Information
Posts: 248
Joined: 18 Feb 2011, 19:35
Location: The low lands
Has thanked: 46 times
Been thanked: 96 times

Post by Pruttelherrie »

electrosonic wrote:[ Image ]

(Not my image btw)
What's the 10~22uF for? It can probably be omitted if there's already enough buffering in the rest of the circuit?

User avatar
electrosonic
Breadboard Brother
Information
Posts: 130
Joined: 28 Nov 2008, 16:53
Location: Vancouver, BC
Has thanked: 27 times
Been thanked: 19 times

Post by electrosonic »

I thought the same thing, probably not necessary

Andrew.

User avatar
coldcraft
Diode Debunker
Information
Posts: 725
Joined: 11 Jul 2009, 01:00
Has thanked: 38 times
Been thanked: 85 times

Post by coldcraft »

I have built the original circuit with TQ2-L-5V relays by panasonic and can verify that it works with those as well. I can also verify that using an NPN BJT as a switch to ground to make/break the connection works as well.

One comment, if the power line has a filter cap, the circuit does not reset to bypass on power loss. I do not know if the bistable arrangements fixes this, but I have found if the 9V connection to the relay circuit comes before the series polarity protection then the problem is solved. I don't yet know if the relay circuit can be damaged by reverse polarity power.
Black Dynamite wrote:you need to shut the fuck up when grown folks is talkin.

User avatar
Cub
Cap Cooler
Information
Posts: 458
Joined: 29 Aug 2011, 07:14
Location: The Netherlands
Has thanked: 102 times
Been thanked: 118 times

Post by Cub »

I tried to convert the stripboard layout from page 2 to an IC Protoboard.
So far, I couldn't find a mistake myself, but that doesn't mean there aren't any.
Could you more experienced lads have a look at the attached gif ? :thumbsup

I would have posted the .diy file as well, but:
"The upload was rejected because the uploaded file was identified as a possible attack vector." :shock:
Attachments
Relay-board.gif
I wish I were a chestnut tree, nourished by the sun.
With twigs and leaves and branches and conkers by the ton.

User avatar
brejna
Breadboard Brother
Information
Posts: 118
Joined: 25 Nov 2012, 17:14
Has thanked: 68 times
Been thanked: 62 times

Post by brejna »

moosapotamus wrote:I made PCB/perf layouts for both versions...

Latching SPDT Footswitch
[ Image ]
[ Image ]

Momentary SPDT Footswitch
[ Image ]
[ Image ]

I tried to make them as small and compact as possible while still having a single-sided layout for easy DIY etching. The component numbering follows the schematic that mmolteratx posted here...
viewtopic.php?f=13&t=13295&start=120#p215994

Here it is, for those that do not have Eagle...
[ Image ]



Footprint for the relay in both layouts is setup to ground the circuit input (SND) when bypassed. The momentary switch version is verified by me. The latching switch version should be good too, since it was just copied/pasted.

Thanks, mictester!

~ Charlie
Is this going to work with TAKAMISAWA RY5W-K 5V? If I make adjustments to for relay lead spacing.
Brane

User avatar
brejna
Breadboard Brother
Information
Posts: 118
Joined: 25 Nov 2012, 17:14
Has thanked: 68 times
Been thanked: 62 times

Post by brejna »

it works, I don't know if there is any popping but it is working. There are pulldown resistors on the layout if there is any popping.
Attachments
Takamisawa_PNP.png
Switch_Takamisawa_layout.png
Switch_Takamisawa.png

User avatar
Mrdorbe
Information
Posts: 10
Joined: 14 Jan 2013, 21:51
Has thanked: 5 times
Been thanked: 1 time

Post by Mrdorbe »

hey guys, I tried to build the relay true baypass layout for momentary switch, and funny thing happened, it worked with a certien power suplly but not with any other,,, i tried it with 5 diferent regulated power suplies and only the led worked, the relay wouldnt switch but with one specific dc power suplly it did...

i dont undrstand why.. :?:

i build the vertion with the momentary switch and installed it in a boss pedal.
I used all the parts specified in the layout, no replacements.
The regulated power supply that worked is 600mA
And the others I tried are between 300mA-1200mA.

User avatar
JFace
Degoop Doctor
Information
Posts: 6
Joined: 08 Feb 2012, 02:18
Been thanked: 37 times

Post by JFace »

Is there any advantage of using a 14 pin logic chip (40106, 4093) over using a 555 timer? It seems as though having a smaller footprint would be ideal if the functionality is the same.

User avatar
mmolteratx
Degoop Doctor
Information
Posts: 508
Joined: 19 Dec 2009, 01:50
Has thanked: 93 times
Been thanked: 619 times

Post by mmolteratx »

Mrdorbe wrote:hey guys, I tried to build the relay true baypass layout for momentary switch, and funny thing happened, it worked with a certien power suplly but not with any other,,, i tried it with 5 diferent regulated power suplies and only the led worked, the relay wouldnt switch but with one specific dc power suplly it did...

i dont undrstand why.. :?:

i build the vertion with the momentary switch and installed it in a boss pedal.
I used all the parts specified in the layout, no replacements.
The regulated power supply that worked is 600mA
And the others I tried are between 300mA-1200mA.
Measure the voltage at the power pin of the inverter.
JFace wrote:Is there any advantage of using a 14 pin logic chip (40106, 4093) over using a 555 timer? It seems as though having a smaller footprint would be ideal if the functionality is the same.
Power draw is lower with an inverter.

Post Reply