Diaz Texas Ranger biasing

Forum dedicated to helping people debug and troubleshoot non-functional pedals or builds. Please use an clear and informative title, indicating circuit and basic problem. Don't forget to mark the issue as fixed if this is the case.
User avatar
TheGunn
Information
Posts: 18
Joined: 30 Dec 2022, 13:05
Has thanked: 1 time
Been thanked: 2 times

Post by TheGunn »

Hi everybody!
I built Diaz Texas Ranger clone with silicone transistor. It sounds fine until you max the guitar volume pot - then it sounds very farty. The voltage on the collector is 8v with the 68 k resistor. I tried swapping transistors and increasing value of 68k resistor but when it's 100k and voltage at collector is around 7v I still get that farty sound. Anyone knows is it normal or what should be voltage on the collector in this circuit? I suggested myself with Rangemaster bias voltage that should sit in between 6.8-7v. Transistors i used were between 100-300 hfe. Any help appreciated :) Image

User avatar
plush
Cap Cooler
Information
Posts: 640
Joined: 08 Dec 2015, 09:29
Location: Moscow, Evil Russia
Has thanked: 36 times
Been thanked: 171 times

Post by plush »

Adding base resistor of some value might help.

User avatar
Manfred
Tube Twister
Information
Posts: 1937
Joined: 04 Apr 2009, 23:42
Has thanked: 1671 times
Been thanked: 1344 times

Post by Manfred »

Take the component values from this circuit including the BIAS trimming potentiometer:
StrangMasterSchematic.jpg
Last edited by Manfred on 31 Dec 2022, 09:18, edited 1 time in total.

User avatar
mauman
Resistor Ronker
Information
Posts: 419
Joined: 17 Jun 2017, 20:01
Location: Texas, US
Has thanked: 423 times
Been thanked: 183 times

Post by mauman »

Here's the thread with Manfred's analysis and a larger schematic: viewtopic.php?p=275152

User avatar
Manfred
Tube Twister
Information
Posts: 1937
Joined: 04 Apr 2009, 23:42
Has thanked: 1671 times
Been thanked: 1344 times

Post by Manfred »

mauman wrote: 31 Dec 2022, 04:40 Here's the thread with Manfred's analysis and a larger schematic: viewtopic.php?p=275152
In the post above I replaced the linked image of the schematic by a larger one.

here is a copy of the images with the data I measured later, which I have inserted in the topic of the link above.
Maybe the measured values will help.
ThrobakStrangMaster Transistor Data Measurements.jpg
ThrobakStrangMaster Transistor Data Measurements.jpg (18.11 KiB) Viewed 2068 times
ThrobakStrangMaster DC-Measurements.jpg

User avatar
TheGunn
Information
Posts: 18
Joined: 30 Dec 2022, 13:05
Has thanked: 1 time
Been thanked: 2 times

Post by TheGunn »

I've tried it with 250k bias potentiometer and even with collector voltage around 5v it was still farty (checked with both humbuckers and single coils).

User avatar
Manfred
Tube Twister
Information
Posts: 1937
Joined: 04 Apr 2009, 23:42
Has thanked: 1671 times
Been thanked: 1344 times

Post by Manfred »

What transistor are you currently using in the circuit
Can you measure the DC values at the transistor pins when the emitter resistor is set to a value of about 70 kiloohms.

User avatar
TheGunn
Information
Posts: 18
Joined: 30 Dec 2022, 13:05
Has thanked: 1 time
Been thanked: 2 times

Post by TheGunn »

I rebuilt it with socket for transistor. I tried 2n3904 and 2n5088 (though I think they are fakes and they are something like 350+ hfe), BC109C, BF257 (hfe between 45-100), BSY56 (hfe 70) and 2n708 (hfe 40). It sounded best with 2n708 but even with bias at 7v if I hit strings harder it still sounds farty (it doesn't sound like overdrive but like misbiased transistor).

User avatar
Manfred
Tube Twister
Information
Posts: 1937
Joined: 04 Apr 2009, 23:42
Has thanked: 1671 times
Been thanked: 1344 times

Post by Manfred »

I ran a circuit simulation using the 2n708 transitor.
I recorded the output signal and the signal at the base of the transistor.
Up to an input signal level of less than 600 millivolts peak, the shape output signal is rounded. Above 600 millivolts peak, sharp edges and corners appear in the shape of the output signal.
This happend because at this signal level the transistor goes into saturation, the sinusoidal signal at the base starts to flatten at the positive half-wave.
The output signal contains through the corners and edges and thus also unwanted harmonics that sound unpleasant.
I inserted a 22 kiloohms resistor between input and the 100 Kiloohms resistor, now the signal remained peak rounded to less than 1000 millivolts.
Diaz Rangmaster Input 200mVpeak to 600mVpeak.jpg

User avatar
TheGunn
Information
Posts: 18
Joined: 30 Dec 2022, 13:05
Has thanked: 1 time
Been thanked: 2 times

Post by TheGunn »

Does anyone know if Texan Twang with silicon transistor differs from schematic posted earlier? I heard that it includes NTE123AP transistor. Maybe it was chosen for some reason?

User avatar
Manfred
Tube Twister
Information
Posts: 1937
Joined: 04 Apr 2009, 23:42
Has thanked: 1671 times
Been thanked: 1344 times

Post by Manfred »

The NTE123AP is a transistor type with low hFE as well as the 2N708.
SJNTE123AP_DATA_E-1.pdf
(63.32 KiB) Downloaded 78 times
2N708-3.pdf
(45.88 KiB) Downloaded 62 times

User avatar
TheGunn
Information
Posts: 18
Joined: 30 Dec 2022, 13:05
Has thanked: 1 time
Been thanked: 2 times

Post by TheGunn »

Lately I'll probably try this circuit out with bc547, 2n2222, 2n3904(this time genuine :lol: ) and maybe 2n4401.

User avatar
Manfred
Tube Twister
Information
Posts: 1937
Joined: 04 Apr 2009, 23:42
Has thanked: 1671 times
Been thanked: 1344 times

Post by Manfred »

I wrote:
I inserted a 22 kiloohms resistor between input and the 100 Kiloohms resistor, now the signal remained peak rounded to less than 1000 millivolts.
Did you try this?

User avatar
TheGunn
Information
Posts: 18
Joined: 30 Dec 2022, 13:05
Has thanked: 1 time
Been thanked: 2 times

Post by TheGunn »

Using 2n708 attack was way less agressive compared to original pedal records and using 22k resistor would even make it worse, so I didn't try it.

User avatar
Manfred
Tube Twister
Information
Posts: 1937
Joined: 04 Apr 2009, 23:42
Has thanked: 1671 times
Been thanked: 1344 times

Post by Manfred »

...and using 22k resistor would even make it worse, so I didn't try it.
I am sorry, maybe you misunderstood what I meant.
I meant inserting the 22k resistor between the input and the connection point of the first 100k resistor and the 0.005uF capacitor.
If not, how do you think that resistor would make it worse?

User avatar
TheGunn
Information
Posts: 18
Joined: 30 Dec 2022, 13:05
Has thanked: 1 time
Been thanked: 2 times

Post by TheGunn »

I mean that as far as I know adding resistor like this should decrease input signal. And since transistor is lower hfe effect lost some attack. So if I add a resistor between input and pulldown resistor I think that it will lose even more definition. Am I wrong?

User avatar
FiveseveN
Cap Cooler
Information
Posts: 591
Joined: 25 Oct 2009, 21:20
Location: Romania
Has thanked: 215 times
Been thanked: 116 times
Contact:

Post by FiveseveN »

TheGunn wrote: 12 Jan 2023, 07:04 as far as I know adding resistor like this should decrease input signal
Right! Because you said
if I hit strings harder it still sounds farty
So the solution is to scale the signal down so it doesn't hit the
Image
Ignorance more frequently begets confidence than does knowledge. (Charles Darwin)

User avatar
Manfred
Tube Twister
Information
Posts: 1937
Joined: 04 Apr 2009, 23:42
Has thanked: 1671 times
Been thanked: 1344 times

Post by Manfred »

TheGunn wrote: 12 Jan 2023, 07:04 I mean that as far as I know adding resistor like this should decrease input signal. And since transistor is lower hfe effect lost some attack. So if I add a resistor between input and pulldown resistor I think that it will lose even more definition. Am I wrong?
Yes, the signal at the base is reduced by about 36%. Is the definition loss just an assumption of yours or have you tried it in the real circuit?
I think it is a general problem of the rangemaster circuits, that they were designed in a time when the pickups still delivered lower output levels than the modern ones of today.

User avatar
TheGunn
Information
Posts: 18
Joined: 30 Dec 2022, 13:05
Has thanked: 1 time
Been thanked: 2 times

Post by TheGunn »

I mean this circuit with 2n708 it was almost no boost and definitely attack was less aggressive. Tried BC547B with 340 hfe and it still sounds unpleasant at maxed guitar volume pot. Maybe I'll try resistor at the input with this transistor.

User avatar
Manfred
Tube Twister
Information
Posts: 1937
Joined: 04 Apr 2009, 23:42
Has thanked: 1671 times
Been thanked: 1344 times

Post by Manfred »

It is not possible to simply replace each BJT transistor with another without replacing the components values of the surrounding circuit.
A strongly different Hfe means that the values of the base voltage divider must be adjusted.

Try the following values for using the BC547.
BC547B Try.jpg
BC547B Try.jpg (23.67 KiB) Viewed 1541 times

Post Reply